Frequency converter FKO - Brinkmann Pumps

More documents

Recommendations

Info

Installation Fig. 9: Wiring 1. Release the screw (1) to remove the contact plate from the adapter plate. The (M6) PE connection (3) is underneath this contact plate. 2. Guide the connection cable from the motor to the adapter plate through the integrated EMC screw connection. 3. This connection has to be made to the same ground potential of the motor. The cross-section of the equipotential bonding line must correspond to at least the cross-section of the power cord. 4. Reattach the contact plate using the screw (1). 28 Operating manual FKO
Installation 5. Wire the motor cable to contacts U, V, W (and star point in some cases) in the connection terminal, as described in the "Basic connection versions" chapter. Use cable shoes (M5) to do this. 6. Before connecting an available motor PTC to the T1 and T2 terminals, remove the preassembled short-circuit bridge (2). The motor PTC is potential-free after connecting the FKO, therefore it must be connected using a separate motor lead. Replace the dummy screw with a suitable standard screw connection and guide both ends to T1 and T2. Fig. 10: Attaching the drive control 7. Position the drive control (1) on the adapter plate (2) so that the collar of the adapter dips into the opening on the floor of the cooling element. 8. Fasten the control unit to the adapter plate with the help of the screws (3) provided (torque: 4.0 Nm). Operating manual FKO 29
Page 1 and 2: Operating manual Frequency converte
Page 3 and 4: Table of contents 1 Important infor
Page 5 and 6: Overview of installation sizes Dime
Page 7 and 8: Important information Supplemental
Page 9 and 10: Important information ATTENTION! Pl
Page 11 and 12: 1.4.4 Operation WARNING Important i
Page 13 and 14: 1.5 Proper use Important informatio
Page 15 and 16: 2 Overview of the drive control Ove
Page 17 and 18: Installation 3.2.2 Suitable install
Page 19 and 20: 3.2.5 Wiring instructions Installat
Page 21 and 22: 3.3.2 Connections for brake resisto
Page 23 and 24: Terminal no. Designation Configurat
Page 25 and 26: Installation The following figure s
Page 27: Fig. 8: Fastening the adapter plate
Page 31 and 32: 4 Commissioning 4.1 Safety instruct
Page 33 and 34: 4.3 Block diagram Internal potentio
Page 35 and 36: 5 Parameters Parameters This chapte
Page 37 and 38: Stand-by function in PID process co
Page 39 and 40: 5.2.2 Structure of the parameter ta
Page 41 and 42: 1.051 Acceleration 1 Unit: s Relati
Page 43 and 44: 1.130 Reference channel Unit: integ
Page 45 and 46: 1.180 Reset Unit: integer Relations
Page 47 and 48: 5.3.3 Motorized potentiometer Param
Page 49 and 50: 3.052 PID derivative gain Unit: s R
Page 51 and 52: 5.3.5 Analogue inputs For analogue
Page 53 and 54: 4.034/4.064 Alx physical minimum Un
Page 55 and 56: 5.3.8 Digital outputs For digital o
Page 57 and 58: 4.191/4.211 Rel.x on Unit: Relation
Page 59 and 60: Parameters The entire function can
Page 61 and 62: 33.032 Motor power Unit: W Relation
Page 63 and 64: 5.4.2 I 2 T 33.010 I 2 T fact. moto
Page 65 and 66: 34.011 Type of encoder Unit: intege
Page 67 and 68: 5.4.5 Squared characteristic 34.120
Page 69 and 70: Error detection and troubleshooting
Page 71 and 72: Error detection and troubleshooting
Page 73 and 74: 7 Technical data 7.1 General data T
Page 75 and 76: 8 Optional accessories This chapter
Page 77 and 78: === Ende der Liste für Textmarke I
Page 79 and 80:
Notes
Page 81 and 82:
R Reference channel............ 42,
show all

Frequency converter FKO - Brinkmann Pumps

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?