Frequency converter FKO - Brinkmann Pumps

More documents

Recommendations

Info

Installation 3.3.4 Terminal connection diagram Fig 5: Connection diagram The drive control is operational after the 400 V power supply has been switched on. Alternatively, the drive control can be started up by connecting an external 24 V power supply. The settings required for this are described in the “System parameters” chapter. A detailed description of the functions of the drive control can be found in the parameter description. 3.4 Installing the wall-mounted drive control 3.4.1 Suitable installation location for wall mounting � Ensure that the installation location for a FKO wall mounting meets the following conditions: – The drive control has to be mounted on an even and fixed surface. – The drive control may only be mounted on non-flammable bases. – There must be a minimum of 20 cm clearance all around the drive control to ensure free convection. 24 Operating manual FKO
Installation The following figure shows the assembly dimensions and the free spaces required for installing the drive control. Fig. 6: Minimum clearances For the "wall mounting" version, the line length between the motor and FKO may not exceed 5 m. A screened cable with the required cross-section must be used. There must be a PE connection (underneath the wall mounting's terminal board)! Operating manual FKO 25
Page 1 and 2: Operating manual Frequency converte
Page 3 and 4: Table of contents 1 Important infor
Page 5 and 6: Overview of installation sizes Dime
Page 7 and 8: Important information Supplemental
Page 9 and 10: Important information ATTENTION! Pl
Page 11 and 12: 1.4.4 Operation WARNING Important i
Page 13 and 14: 1.5 Proper use Important informatio
Page 15 and 16: 2 Overview of the drive control Ove
Page 17 and 18: Installation 3.2.2 Suitable install
Page 19 and 20: 3.2.5 Wiring instructions Installat
Page 21 and 22: 3.3.2 Connections for brake resisto
Page 23: Terminal no. Designation Configurat
Page 27 and 28: Fig. 8: Fastening the adapter plate
Page 29 and 30: Installation 5. Wire the motor cabl
Page 31 and 32: 4 Commissioning 4.1 Safety instruct
Page 33 and 34: 4.3 Block diagram Internal potentio
Page 35 and 36: 5 Parameters Parameters This chapte
Page 37 and 38: Stand-by function in PID process co
Page 39 and 40: 5.2.2 Structure of the parameter ta
Page 41 and 42: 1.051 Acceleration 1 Unit: s Relati
Page 43 and 44: 1.130 Reference channel Unit: integ
Page 45 and 46: 1.180 Reset Unit: integer Relations
Page 47 and 48: 5.3.3 Motorized potentiometer Param
Page 49 and 50: 3.052 PID derivative gain Unit: s R
Page 51 and 52: 5.3.5 Analogue inputs For analogue
Page 53 and 54: 4.034/4.064 Alx physical minimum Un
Page 55 and 56: 5.3.8 Digital outputs For digital o
Page 57 and 58: 4.191/4.211 Rel.x on Unit: Relation
Page 59 and 60: Parameters The entire function can
Page 61 and 62: 33.032 Motor power Unit: W Relation
Page 63 and 64: 5.4.2 I 2 T 33.010 I 2 T fact. moto
Page 65 and 66: 34.011 Type of encoder Unit: intege
Page 67 and 68: 5.4.5 Squared characteristic 34.120
Page 69 and 70: Error detection and troubleshooting
Page 71 and 72: Error detection and troubleshooting
Page 73 and 74: 7 Technical data 7.1 General data T
Page 75 and 76:
8 Optional accessories This chapter
Page 77 and 78:
=== Ende der Liste für Textmarke I
Page 79 and 80:
Notes
Page 81 and 82:
R Reference channel............ 42,
show all

Frequency converter FKO - Brinkmann Pumps

Create successful ePaper yourself

Delete template?

Save as template?