Edwards, nEXT Turbomolecular Pumps, nEXT240, nEXT300 and ...

More documents

Recommendations

Info

B800-00-880 Issue B Installation Figure 18 - Maximum relative humidity to avoid condensation with water cooling Page 44 © Edwards Limited 2009. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
B800-00-880 Issue B 4 Operation WARNING Do not operate the nEXT pump unless it is connected to your vacuum system. If you do, the pump rotor can cause injury. The pump rotor rotates at very high speeds and the rotating blades might not be visible. Operation Before operating the pump, it is worthwhile configuring the various Controller settings so that they are suitable for your application. If your system is designed to operate with Parallel control and monitoring, you will not have the facility to change the majority of the Controller settings once the nEXT pump is installed on your system. The pump is supplied with all settings at factory default values, as shown in Table 16. If you wish to change any of the Controller settings, make sure you do this separately before installing the nEXT pump on your system. To configure the nEXT pump you could use your own serial system. Section 4.1 details the commands that you will need to configure the Controller. Alternatively you could use the Edwards TIC Turbo and Instrument Controller or TIC Turbo Controller. Further information regarding this is detailed in Section 4.2. Note: The standby speed may be adjusted using the button on the controller as described in Section 4.1.4. If you intend to operate the nEXT pump with Parallel control and monitoring and you do not wish to reconfigure the Controller settings, go straight to Section 4.3. 4.1 Configuring the nEXT pump using serial commands Refer to Table 16 for a summary of the full set of serial commands, parameter ranges and factory defaults for each setting. The following sections describe the settings in more detail. 4.1.1 Power limit setting Table 21 shows the power limit setting options for the nEXT pumps. The pump is supplied to you with a default power limit as shown. If this limit is not suitable for your application, you can change it to any value between the maximum and minimum shown. Table 21 - Power limit setting Maximum value setting Minimum value setting Default power setting 200 W 50 W 160 W Send the command as follows (where the 'd' characters represent the value in Watts that you are trying to set. For example, if you want to set the limit to 90 W, type 90). The reply you receive will be in the following format: Command ! S 8 5 5 sp d d d cr Reply S 8 5 5 sp r cr The Power Limit Setting is now stored in memory within the nEXT pump. To check what power limit is set, you can send a query as follows: Command ? S 8 5 5 cr © Edwards Limited 2009. All rights reserved. Page 45 Edwards and the Edwards logo are trademarks of Edwards Limited.
Page 1: Instruction Manual B800-00-880 Issu
Page 4 and 5: B800-00-880 Issue B Contents 3.7.1
Page 6 and 7: B800-00-880 Issue B Contents 11 Log
Page 8 and 9: B800-00-880 Issue B Introduction 1.
Page 10 and 11: B800-00-880 Issue B Introduction If
Page 12 and 13: B800-00-880 Issue B Introduction co
Page 14 and 15: B800-00-880 Issue B Technical data
Page 30 and 31: B800-00-880 Issue B This page has b
Page 32 and 33: B800-00-880 Issue B Installation 3.
Page 34 and 35: B800-00-880 Issue B Installation
Page 36 and 37: B800-00-880 Issue B Installation Th
Page 40 and 41: B800-00-880 Issue B Installation se
Page 42 and 43: B800-00-880 Issue B Installation Fi
Page 44 and 45: B800-00-880 Issue B Installation Sp
Page 48 and 49: B800-00-880 Issue B Installation Op
Page 52 and 53: B800-00-880 Issue B Operation The r
Page 54 and 55: B800-00-880 Issue B Operation 4.1.6
Page 56 and 57: B800-00-880 Issue B Operation Note:
Page 58 and 59: B800-00-880 Issue B Operation The g
Page 60 and 61: B800-00-880 Issue B Operation You w
Page 62 and 63: B800-00-880 Issue B Operation Figur
Page 64 and 65: B800-00-880 Issue B Operation 4.9.4
Page 68 and 69: B800-00-880 Issue B Maintenance CAU
Page 70 and 71: B800-00-880 Issue B Maintenance No
Page 72 and 73: B800-00-880 Issue B Maintenance 7 S
Page 74 and 75: B800-00-880 Issue B Maintenance 5.5
Page 76 and 77: B800-00-880 Issue B Maintenance Bit
Page 80 and 81: B800-00-880 Issue B Service, spares
Page 82 and 83: B800-00-880 Issue B Service, spares
Page 84: B800-00-880 Issue B Service, spares

Edwards, nEXT Turbomolecular Pumps, nEXT240, nEXT300 and ...

Create successful ePaper yourself

Delete template?

Save as template?