Full Custom IC Desig..

More documents

Recommendations

Info

vi. Step size= the difference between each two reading. g. Now check the enable box at the lower left corner. h. Click OK. Figure 22: Transient Simulation Window San Francisco State University Nano‐electronics and Computing Research Lab 22
Figure 23: DC Simulation Window 3. The following step is to choose the desired simulations results and select the nodes in the circuit to measure. In section TWO of Fig: 20 do the following steps: To setup the circuit output voltage: a. Click under the output field, and write “Vout” or a name for an output variable of the inverter. b. Click under the expression column and choose the output node from the schematic. In this case, click on and select the wire labeled “vout” as shown below in figure 24 in the schematic window. You can also write an equation that uses the values of some nodes in that schematic. c. Under analysis, just check the simulation option. Select the one that applies for this variable. (For now select both of them dc and tran). To setup the circuit input voltage: San Francisco State University Nano‐electronics and Computing Research Lab 23
Page 1 and 2: Full Custom IC Design Flow Tutorial
Page 3 and 4: Introduction This manual assumes yo
Page 5 and 6: Figure 1: Shell commands Custom Des
Page 7 and 8: Figure 4: New Cell View After you c
Page 9 and 10: Figure 8: PMOS and NMOS Next add wi
Page 11 and 12: Adding Pins To add pins to the sche
Page 13 and 14: Figure 13: Schematic with Pins San
Page 15 and 16: Figure 15: Inverter Symbol You may
Page 17 and 18: Figure 17: Drawing an Instance of a
Page 19 and 20: Figure 19: Edit property You final
Page 21: 1. Choose the appropriate Models fo
Page 25 and 26: Figure 24: Clicking on the Schemati
Page 27 and 28: Figure 26: Save State Window To run
Page 29 and 30: Figure 28: Transient Analysis Wave
Page 31 and 32: Figure 31: Grouping Waveforms Delay
Page 33 and 34: Figure 33: Delay Waveform Measureme
Page 35 and 36: Figure 35: Rise/Fall Waveform Measu
Page 37 and 38: Figure 37: Average Waveform Measure
Page 39 and 40: Figure 39: Frequency Waveform Measu
Page 41 and 42: Figure 41: Layout Window Go to rule
Page 43 and 44: Figure 44: Layout with NWell and Di
Page 45 and 46: Figure 46: Drawing a Path San Franc
Page 47 and 48: Figure 48: Drawing Contacts Select
Page 49 and 50: Figure 51: Labeling Connections San
Page 51 and 52: Figure 53: DRC Setup Click OK. Afte
Page 53 and 54: Figure 57: DRC Errors San Francisco
Page 55 and 56: In the layout window go to Verifica
Page 57 and 58: Under Control Variables tab set DEC
Page 59 and 60: Figure 63: LVS Done Confirmation Al
Page 61 and 62: Figure 66: LPE Setup Main Tab Under
Page 63 and 64: Under Output Options tab type make
Page 65 and 66: Figure 70: Passing LPE After LPE ha
Page 67 and 68: Figure 72: Parasitic View Zoom You
Page 69 and 70: Figure 74: Testbench Circuit for In
Page 71 and 72: Figure 76: Hierarchy Editor In orde
Page 73 and 74:
Figure 78: Open Design with Parasit
Page 75 and 76:
Now go ahead and simulate your circ
Page 77 and 78:
For the pins, go to Add Pins and p
Page 79 and 80:
Figure 84: Ring Oscillator Symbol N
Page 81 and 82:
window. In the add instance window,
Page 83 and 84:
instances of the inverter layout on
Page 85 and 86:
Figure 90: Ring Oscillator Layout F
Page 87 and 88:
Debug any DRC errors that come up.
Page 89 and 90:
At this point if there are any LVS
Page 91 and 92:
If LPE ran successfully, a parasiti
Page 93 and 94:
Figure 99: Configurations File Setu
Page 95 and 96:
Figure 101: Ring Oscillator Testben
Page 97 and 98:
Figure 103: Setting up Convergence
show all

Full Custom IC Desig..

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?