Print Station Operator's Guide - Kodak

More documents

Recommendations

Info

Chapter 2. Operator Controls Title Screen Title Screen When the print station is turned on, the control terminal shows the results of internal diagnostics and then displays the fluid controller software TITLE screen (Figure 2.1). From this screen, the operator can press any key to display the CONTROL MENU screen to access various print station control functions. Figure 2.1 Fluid controller software title screen Fluid Controller Software Release 3.xx Serial Number: 999999 Press any key Control Menu Screen From the CONTROL MENU screen (Figure 2.2), the operator can: • Select a function by entering the associated number. • Select a function by using UP ARROW or DOWN ARROW to move the cursor and pressing ENTER TO select the function when highlighted. To obtain additional information about functions available from the CONTROL MENU screen, press F1 while the screen is active. Figure 2.2 Control menu screen ** CONTROL MENU ** Function Selections 1 Ready 2 Clean 3 Shut down 4 Clean - long 5 ---------- 6 Adjust 7 Remote/Line 8 Service menu 9 Quit Choose a function, enter the number Press F1/F2 key for HELP. After a function is selected, a menu or screen associated with the selected item is displayed. Refer to Table 2.1 for detailed function information and uses. All functions can be accessed at any time, however, the shut down function should always be performed before initiating a quit function. Caution: Shut down function MUST be performed before performing quit function or ink spills may occur at the printhead. 2 - 2 DT2 Print Station
Chapter 2. Operator Controls Control Menu Screen Table 2.1 Function Control menu functions Use 1 Ready Brings the printhead to normal operational condition. Selecting this function displays the PRINTHEAD READY status screen. When the printhead is ready for normal operation, the PRINTHEAD READY CYCLE status screen is displayed. 2 Clean Starts a 1-minute printhead clean cycle without sonic stimulation. Typically, this function is used to clean the printhead after a short shutdown (up to a few hours) or when removing the eyelid/ installing the catchpan to perform printhead servicing. Refer to Chapter 4, “Messages” for symptoms of print problems. Selecting this function displays the PRINTHEAD CLEAN status screen. 3 Shut down Starts a 15-minute shut down cycle to remove all fluid from the printhead. Typically this function is used to shut down the printhead at the end of the day or anytime after ink circulation in the printhead has occurred and the quit function will be selected. Selecting this function displays the SHUTDOWN PRINTHEAD status screen. 4 Clean - long Starts a 5-minute printhead clean cycle without sonic stimulation. Typically, this function is used the clean the printhead after an overnight shutdown. Selecting this function displays the LONG CLEAN status screen. 5 --------- No function. 6 Adjust Used to change the stimulation phase, charge voltage, and ink pressure settings. Selecting this function displays the PARAMETER ADJUSTMENTS screen (Figure 2.3) used to change settings and improve printhead performance. • Stim phase can be changed in 1 segment increments (maximum change of 15 segments possible) • Charge voltage can be changed in 0.4 VDC increments (maximum change of ± 10 VDC possible within operating range set by supervisor) • Ink pressure can be changed in 0.07 PSI increments (maximum change of ± 1 PSI possible) 7 Remote/line Used to determine whether the print station or the data station controls when the eyelid opens and closes, or to allow printing by other print stations installed in printing system when the print station is inactive. The data station normally controls the eyelid when running a job. Selecting this item displays the REMOTE/SERVICE screen (Figure 2.4). • Remote eyelid - data station controls the printhead eyelid positioning. Used for normal print operations. • Local eyelid - print station controls the printhead eyelid position, Used for printhead cleaning and maintenance. • On-Line - print station printing is controlled by data station. • Off-line - Print station will not print, but other print stations in system can print. Operator’s Guide 2 - 3
Page 1: VERSAMARK DT2 Print Station Operato
Page 4 and 5: FCC Compliance Statement This equip
Page 6 and 7: Scope Text Notations This manual us
Page 9 and 10: Contents Chapter 1. Overview Print
Page 11 and 12: Chapter 1. Overview The KODAK VERSA
Page 13: Chapter 1. Overview Ink and Repleni
Page 18 and 19: Chapter 2. Operator Controls Servic
Page 20 and 21: Chapter 2. Operator Controls Status
Page 22 and 23: Chapter 2. Operator Controls Status
Page 25 and 26: Chapter 3. Print Station Operation
Page 33: Chapter 3. Print Station Operation
Page 36 and 37: Chapter 4. Messages Figure 4.2 Erro
Page 39 and 40: Appendix A. Parameters Adjustment S
Page 45 and 46: Glossary This glossary of terms app
Page 47 and 48: Glossary character cell An imaginar
Page 49 and 50: Glossary downstream The direction t
Page 51 and 52: Glossary IP address Network address
Page 53 and 54: Glossary page buffer Memory in a RI
Page 55 and 56: Glossary run slow To run the web at
Page 57: Glossary umbilical The part of the
Page 62: Eastman Kodak Company 3000 Research

Print Station Operator's Guide - Kodak

Create successful ePaper yourself

Delete template?

Save as template?