Print Station Operator's Guide - Kodak

More documents

Recommendations

Info

Appendix A. Parameters Adjustment Screen Functions Stim Phase Adjustment Stim Phase Adjustment Note: The phase setting may require adjustment again when the print station reaches a maximum operating temperature. The operator can choose any of 16 phase settings during large environmental changes. Find and record the stim phase window with the following steps. 1. From the CONTROL MENU screen, select function 8 Service Menu. 2. Select function 9 Parameters Menu, and enter the password. 3. Select function 4 Stim Phase. 4. Select each of the 16 different phase settings. Record all phase settings that print test patterns of good quality. 5. Examine the printed test patterns. Several adjacent settings should provide good print quality. These phase settings are the phase window. 6. Find the center of the phase window, then set the phase one value above the center. This is the set point. 7. Print test patterns at the expected job speed. Check the results for ghosting. Charge Voltage Adjustment Caution: Do not change the center point of the pressure by more than 1.5 psi (10.3 kPa). Note: The operator has a range of 10 VDC above and below the center point for a total range of 20 VDC. Note: Extreme cases of pickout or dark defect may need changes of 5 to 10 VDC to correct printhead performance. Small changes of about 2 VDC can correct minor cases of pickout or dark defect. Use the following procedure to change the center point of the operator charge voltage adjustment range. Find and record the charge voltage window with the following steps: 1. From the CONTROL MENU screen, select function 8 Service Menu. 2. Select function 9 Parameters Menu, and enter the password. 3. Select 5 Charge Voltage. 4. Lower the charge voltage to find the lowest charge voltage that will allow printing without dark defect. Lowest charge voltage setting: VDC. A - 4 DT2 Print Station
Appendix A. Parameters Adjustment Screen Functions Station Number 5. Raise the charge voltage to find the highest charge voltage that will allow printing without pickout. Highest charge voltage setting: VDC. 6. Calculate the set point of the charge voltage range. a. Subtract the lower charge voltage from the upper charge voltage. This value is the charge voltage window. b. Divide the charge voltage window value by 2 and add the result to the lower charge voltage. 7. Set the center point of the range to this result. 8. Press ESC, then select 9 Service Menu and 8 Control Menu to return to the CONTROL MENU screen. 9. Print test patterns at the expected job speed. Check the results for pickout and dark defect. Station Number Note: It is recommended that F1 be pressed and the amplifying information read before setting/changing the station number of the print station. The station number setup is used to assign either station numbers or station and RIP numbers to the print station. The station number is used by operators and supervisors to determine which print station/head is printing data. Standby Note: Ink circulation can also be accomplished by pressing CTRL + z any time the print station is operational. Selecting standby circulates ink through the print station and printhead. Setup Menu The information and selection provided in the SETUP MENU screen should be performed at the time of initial install or on an as required basis. The include: PH Height Used to provide the height of the printhead above the base of the print station. This information is used to set the default levels for the print station pressure and vacuum parameters. Ink Number Used to provide the ink number to the print station. The ink number is used to set the default concentration value. The print station must be shutdown before changing this number. Operator’s Guide A - 5
Page 1: VERSAMARK DT2 Print Station Operato
Page 4 and 5: FCC Compliance Statement This equip
Page 6 and 7: Scope Text Notations This manual us
Page 9 and 10: Contents Chapter 1. Overview Print
Page 11 and 12: Chapter 1. Overview The KODAK VERSA
Page 13: Chapter 1. Overview Ink and Repleni
Page 16 and 17: Chapter 2. Operator Controls Title
Page 18 and 19: Chapter 2. Operator Controls Servic
Page 20 and 21: Chapter 2. Operator Controls Status
Page 22 and 23: Chapter 2. Operator Controls Status
Page 25 and 26: Chapter 3. Print Station Operation
Page 33: Chapter 3. Print Station Operation
Page 36 and 37: Chapter 4. Messages Figure 4.2 Erro
Page 39 and 40: Appendix A. Parameters Adjustment S
Page 41: Appendix A. Parameters Adjustment S
Page 45 and 46: Glossary This glossary of terms app
Page 47 and 48: Glossary character cell An imaginar
Page 49 and 50: Glossary downstream The direction t
Page 51 and 52: Glossary IP address Network address
Page 53 and 54: Glossary page buffer Memory in a RI
Page 55 and 56: Glossary run slow To run the web at
Page 57: Glossary umbilical The part of the
Page 62: Eastman Kodak Company 3000 Research

Print Station Operator's Guide - Kodak

Create successful ePaper yourself

Delete template?

Save as template?