SATA RAID Drive Enclosure - StarTech.com

More documents

Recommendations

Info

Hardware Guide Front Panel (closed) Instruction Manual Rear Panel Power Button Power Port eSATA port Front Panel (open) Error Condition Indicator OK Indicator Drive Bays Key Lock Front Panel Door 3 Safety latch
Hard drive installation Instruction Manual 1. Open the Front Panel Door, exposing the individual Drive Bays. 2. To remove one of the Drive Bays from the enclosure, slide the Safety Latch on the front panel of the bay, to the left. Gently press the cover of the Drive Bay until you hear a click, allowing the Retaining Arm to move freely. Grasp the Retaining Arm and pull the Drive Bay from the enclosure. 3. Align the screwholes provided on the base of the Drive Bay, with the screws provided on the base of the hard drive. Secure the hard drive to the metal base of the Drive Bay removed in step 2, using the included screws as necessary. 4. Once the drive has been secured to the Drive Bay, replace the Drive Bay by gently sliding it into the empty slot, ensuring the Drive Bay is properly resting on the internal guide rails provided. The SATA data and power connectors located on the back of the hard drive should be in direct contact with the connectors located internally at the back of the enclosure. 5. Gently press the Retaining Arm (see step 2) until it locks back in place, now flush with the other drive bays. 6. Slide the Safety Latch to the right, to ensure that the installed drive is not accidentally released from the enclosure. 7. Repeat steps 1-6, for the remaining hard drives you wish to install. 8. Once you have secured each hard drive within the enclosure, close the Front Panel Door. Optionally, you can lock the Front Panel Door in place, using the keys provided, by turning the lock 1/4 turn in a clockwise direction. Connecting the Drive Enclosure to the computer To connect the SAT3550ESR Drive Enclosure to the host computer: Connect one end of a standard eSATA cable to the port located on the rear panel of the Drive Enclosure; connect the remaining end of the eSATA cable to the eSATA port provided by the the newly installed host controller on the host computer. To power the SAT3550ESR Drive Enclosure: Connect the female portion of the included power cable to the male power port located on the rear panel of the Drive Enclosure. Connect the remaining end of the power cable to an available power outlet. Press and hold the Power button for three seconds, (located on the front of the Drive Enclosure). Verify that the drives are detected by the operating system (in Windows, for example, browse to My Computer, where the newly attached drives should appear). 4
Page 1 and 2: SATA RAID Drive Enclosure 5 Drive 3
Page 3 and 4: Table of Contents Instruction Manua
Page 5: Installation Instruction Manual Hos
Page 9 and 10: Status Window Instruction Manual Th
Page 11 and 12: Basic Configuration Instruction Man
Page 13 and 14: Instruction Manual ***Basic Storage
Page 15 and 16: Toolbar button functions Instructio
Page 17 and 18: Instruction Manual Select SAFE (RAI
Page 19 and 20: Manage Configuration files Instruct
Page 21 and 22: Partition Configured Volumes Instru
Page 23 and 24: Instruction Manual 8. You will rece
Page 25 and 26: Instruction Manual Enclosure are ac
Page 27 and 28: Instruction Manual c) The message i
Page 29 and 30: Instruction Manual The ‘AllowAdva
Page 31 and 32: Instruction Manual Monitoring fan s
Page 33 and 34: Status Indicators for ! and OK LEDs
Page 35 and 36: SAFE and BIG Instruction Manual A s
Page 37: About StarTech.com StarTech.com is

SATA RAID Drive Enclosure - StarTech.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?