Consultation Draft - National Transport Commission

More documents

Recommendations

Info

Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 other metal (1N1, 1N2) plywood (1D) fibre (1G) plastics (1H1, 1H2) P144 For "Inner packagings", "Receptacles", insert a new line to read: "wood". P144 For "Outer packagings", "Boxes", after "aluminium (4B)", insert a new row to read "other metal (4N)". P144 Amend the entries under "Outer packagings", "Drums" to read: steel (1A1, 1A2) aluminium (1B1, 1B2) other metal (1N1, 1N2) plastics (1H1, 1H2) P200, Paragraph (4): Amend the first line reading "Keys for the column "Special packing provisions"" to read "Special packing provisions". P200, Paragraph (4): Amend the first heading reading "Material compatibility (for gases see ISO 11114-1:1997 and ISO 11114-2:2000" to read "Material compatibility". P200, Paragraph (4): Amend sub-paragraph a to read: "a: Aluminium alloy pressure receptacles must not be used.". P200, Paragraph (4): Amend sub-paragraph d to read: "d: When steel pressure receptacles are used, only those bearing the "H" mark in accordance with 6.2.2.7.4 (p) are permitted.". P200 (4) In special packing provision "k", amend the first sentence to read as follows: "Valve outlets must be fitted with pressure retaining gas-tight plugs or caps having threads that match those of the valves outlets.". Amend the seventh paragraph ("Each valve must have a taper threaded connection…") to read as follows: "Each valve must be capable of withstanding the test pressure of the pressure receptacle and be connected directly to the pressure receptacle by either a taper thread or other means which meets the requirements of ISO 10692-2:2001.". In special packing provision "q", in the first sentence, at the beginning, replace "The valves" with "Valve outlets". In the second sentence, at the end, replace "manifold outlet valve" with 100 CONSULTATION DRAFT
Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 "outlet of the manifold valve" and add "pressure retaining" before "gas-tight plug". Add a new third sentence to read as follows: "Gas-tight plugs or caps must have threads that match those of the valves outlets.". Add the following new special packing provision "ra": "ra: This gas may also be packed in capsules under the following conditions: (a) (b) (c) (d) The mass of gas must not exceed 150 g per capsule; The capsules must be free from faults liable to impair the strength; The leakproofness of the closure must be ensured by an additional device (cap, crown, seal, binding, etc.) capable of preventing any leakage of the closure during transport; The capsules must be placed in an outer packaging of sufficient strength. A package must not weigh more than 75 kg.". P200, Table 2: For UN Nos. 1008, 1076, 1741, 1859, 2189 and 2418, insert "a" in column "Special packing provisions". P200 In Table 2, against UN 1037, add "ra" in column "Special packing provisions". P200, Table 3: For UN No. 1052, insert "a" in column "Special packing provisions". P201 Amend to read as follows: P201 PACKING INSTRUCTION P201 This instruction applies to UN Nos. 3167, 3168 and 3169. The following packagings are authorized: (1) Cylinders and gas receptacles conforming to the construction, testing and filling requirements approved by the competent authority. (2) The following combination packagings provided that the general provisions of 4.1.1 and 4.1.3 are met: Outer packagings: Drums (1A1, 1A2, 1B1, 1B2, 1N1, 1N2, 1H1, 1H2, 1D, 1G); Boxes (4A, 4B, 4N, 4C1, 4C2, 4D, 4F, 4G, 4H1, 4H2); Jerricans (3A1, 3A2, 3B1, 3B2, 3H1, 3H2). CONSULTATION DRAFT 101
Page 1 and 2:
Consultation Draft Model Amendment
Page 3 and 4:
Model Amendment Regulations -Transp
Page 5 and 6:
Schedule 1 - Amendments to the Mode
Page 7 and 8:
(b) (c) (a) (b) (c) (d) (e) (f) a r
Page 9 and 10:
"(4) {Subclause} (3) does not apply
Page 11 and 12:
(2) The prime contractor must retai
Page 13 and 14:
(2) The Competent Authority must ha
Page 15 and 16:
4. Goods too dangerous to be transp
Page 17 and 18:
G These entries must be used for cy
Page 19 and 20:
"(d) a Non-Type I Underslung Segreg
Page 21 and 22:
(4) In 5.2.1.8, at the end of note
Page 23 and 24:
1 IBC with ½ size EIP fully visibl
Page 25 and 26:
"10.2.3.7 Despite 10.2.3.1 and 10.2
Page 27 and 28:
Note 2: In cases of combination veh
Page 29 and 30:
UN HAZCHEM HIN UN HAZCHEM HIN UN HA
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
UN HAZCHEM HIN 3272 3YE (3) 33 3Y 3
Page 37 and 38:
Model Amendment Regulations - Trans
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50: Model Amendment Regulations - Trans
Page 99: Model Amendment Regulations - Trans
Page 129 and 130: Not less than 250 mm Model Amendmen
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159:
show all

Consultation Draft - National Transport Commission

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?