Consultation Draft - National Transport Commission

More documents

Recommendations

Info

Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 When active, these devices must meet defined standards for electromagnetic radiation to ensure that the operation of the device does not interfere with aircraft systems. Additional requirement: Cells or batteries must be protected against short circuit. P904 Amend to read as follows: P904 PACKING INSTRUCTION P904 This instruction applies to UN No. 3245. The following packagings are authorized: (1) Packagings meeting the provisions of 4.1.1.1, 4.1.1.2, 4.1.1.4, 4.1.1.8 and 4.1.3 and so designed that they meet the construction requirements of 6.1.4. Outer packagings constructed of suitable material, and of adequate strength and design in relation to the packaging capacity and its intended use, must be used. Where this packing instruction is used for the transport of inner packagings of combination packagings the packaging must be designed and constructed to prevent inadvertent discharge during normal conditions of transport. (2) Packagings, which need not conform to the packaging test requirements of Part 6, but conforming to the following: (a) (b) An inner packaging comprising: (i) (ii) (iii) primary receptacle(s) and a secondary packaging, the primary receptacle(s) or the secondary packaging must be leakproof for liquids or siftproof for solids; for liquids, absorbent material placed between the primary receptacle(s) and the secondary packaging. The absorbent material must be in a quantity sufficient to absorb the entire contents of the primary receptacle(s) so that any release of the liquid substance will not compromise the integrity of the cushioning material or of the outer packaging; if multiple fragile primary receptacles are placed in a single secondary packaging they must be individually wrapped or separated to prevent contact between them; An outer packaging must be strong enough for its capacity, mass and intended use, and with a smallest external dimension of at least 100 mm. For transport, the mark illustrated below must be displayed on the external surface of the outer packaging on a background of a contrasting colour and must be clearly visible and legible. The mark must be in the form of a square set at an angle of 45° (diamond-shaped) with each side having a length of at least 50 mm; the width of the line must be at least 2 mm and the letters and numbers must be at least 6 mm high. UN 3245 Additional requirement: 114 CONSULTATION DRAFT
Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 P904 PACKING INSTRUCTION P904 Ice, dry ice and liquid nitrogen When dry ice or liquid nitrogen is used as a coolant, the requirements of 5.5.3 apply. When used, ice must be placed outside the secondary packagings or in the outer packaging or an overpack. Interior supports must be provided to secure the secondary packaging in the original position. If ice is used, the outside packaging or overpack must be leakproof. P907 In the second sentence, for "of adequate strength and design" read ", and of adequate strength and design". 4.1.4.1 Add the following new packing instruction: P205 PACKING INSTRUCTION P205 This instruction applies to UN No. 3468. (1) For metal hydride storage systems, the general packing requirements of 4.1.6.1 must be met. (2) Only pressure receptacles not exceeding 150 litres in water capacity and having a maximum developed pressure not exceeding 25 MPa are covered by this packing instruction. (3) Metal hydride storage systems meeting the applicable requirements for the construction and testing of pressure receptacles containing gas of Chapter 6.2 are authorised for the transport of hydrogen only. (4) When steel pressure receptacles or composite pressure receptacles with steel liners are used, only those bearing the "H" mark, in accordance with 6.2.2.9.1(j) must be used. (5) Metal hydride storage systems must meet the service conditions, design criteria, rated capacity, type tests, batch tests, routine tests, test pressure, rated charging pressure and provisions for pressure relief devices for transportable metal hydride storage systems specified in ISO 16111:2008 and their conformity and approval must be assessed in accordance with 6.2.2.5. (6) Metal hydride storage systems must be filled with hydrogen at a pressure not exceeding the rated charging pressure shown in the permanent markings on the system as specified by ISO 16111:2008. (7) The periodic test requirements for a metal hydride storage system must be in accordance with ISO 16111:2008 and carried out in accordance with 6.2.2.6, and the maximum interval between periodic inspections must not exceed five years. 4.1.4.1 Add the following new packing instructions: P206 PACKING INSTRUCTION P206 This instruction applies to UN Nos. 3500, 3501, 3502, 3503, 3504 and 3505. Unless otherwise indicated in this Code, cylinders and pressure drums conforming to the applicable requirements of Chapter 6.2 are authorized. (1) The general packing requirements of 4.1.6.1 must be met. (2) The maximum test period for periodic inspection must be 5 years. (3) Cylinders and pressure drums must be so filled that at 50 °C the non-gaseous phase does not exceed 95% of their water capacity and they are not completely filled at 60 °C. When filled, the internal pressure at 65 °C must not exceed the CONSULTATION DRAFT 115
Page 1 and 2:
Consultation Draft Model Amendment
Page 3 and 4:
Model Amendment Regulations -Transp
Page 5 and 6:
Schedule 1 - Amendments to the Mode
Page 7 and 8:
(b) (c) (a) (b) (c) (d) (e) (f) a r
Page 9 and 10:
"(4) {Subclause} (3) does not apply
Page 11 and 12:
(2) The prime contractor must retai
Page 13 and 14:
(2) The Competent Authority must ha
Page 15 and 16:
4. Goods too dangerous to be transp
Page 17 and 18:
G These entries must be used for cy
Page 19 and 20:
"(d) a Non-Type I Underslung Segreg
Page 21 and 22:
(4) In 5.2.1.8, at the end of note
Page 23 and 24:
1 IBC with ½ size EIP fully visibl
Page 25 and 26:
"10.2.3.7 Despite 10.2.3.1 and 10.2
Page 27 and 28:
Note 2: In cases of combination veh
Page 29 and 30:
UN HAZCHEM HIN UN HAZCHEM HIN UN HA
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
UN HAZCHEM HIN 3272 3YE (3) 33 3Y 3
Page 37 and 38:
Model Amendment Regulations - Trans
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64: Model Amendment Regulations - Trans
Page 113: Model Amendment Regulations - Trans
Page 129 and 130: Not less than 250 mm Model Amendmen
Page 159: Model Amendment Regulations - Trans
show all

Consultation Draft - National Transport Commission

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?