Consultation Draft - National Transport Commission

More documents

Recommendations

Info

Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 (ii) Date of the most recent periodic test (month and year); (iii) Test pressure (in bar gauge or kPa gauge) 2 of the most recent periodic test (if applicable); (iv) Identification mark of the authorized body who performed or witnessed the most recent test. Figure 6.7.2.20.1: Example of identification plate marking Owner’s registration number MANUFACTURING INFORMATION Country of manufacture Year of manufacture Manufacturer Manufacturer’s serial number APPROVAL INFORMATION Approval country Authorized body for design approval Design approval number Shell design code (pressure vessel code) PRESSURES MAWP Test pressure Initial pressure test date: (mm/yyyy) Witness stamp: External design pressure MAWP for heating/cooling system ‘AA’ (if applicable) bar or kPa bar or kPa bar or kPa bar or kPa (when applicable) TEMPERATURES Design temperature range °C to °C MATERIALS Shell material(s) and material standard reference(s) Equivalent thickness in reference steel Lining material (when applicable) CAPACITY Tank water capacity at 20 °C Water capacity of compartment ___ at 20 °C (when applicable, for multi-compartment tanks) litres ‘S’ (if applicable) litres ‘S’ (if applicable) PERIODIC INSPECTIONS / TESTS Test Witness stamp and Test Witness stamp and Test date type test pressure a Test date type test pressure a (mm/yyyy) bar or kPa (mm/yyyy) bar or kPa mm 144 CONSULTATION DRAFT
Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 a Test pressure if applicable.". 6.7.2.20.2 Insert "Portable tank instruction in accordance with 4.2.5.2.6" in the list. 6.7.3 After the heading, insert the following new Note: "NOTE: These requirements also apply to portable tanks intended for the transport of chemicals under pressure (UN Nos. 3500, 3501, 3502, 3503, 3504 and 3505).". 6.7.3.1 In the definition of Design reference temperature, in the second sentence, insert "or liquefied gas propellants of chemicals under pressure" after "non-refrigerated liquefied gas". 6.7.3.1 In sub-paragraph (b) of the definition of Maximum allowable working pressure, add a new sub-paragraph (iii) to read as follows: "(iii) for chemicals under pressure, the MAWP (in bar) given in T50 portable tank instruction for the liquefied gas portion of the propellants listed in T50 in 4.2.5.2.6;". 6.7.3.5.4 In the first sentence, insert "or chemicals under pressure" after "nonrefrigerated liquefied gases". 6.7.3.9.1 and 6.7.4.8.1 After sub-paragraph (d), add the following new subparagraph (e): "(e) The cross sectional flow areas of the spring loaded pressure-relief devices and frangible discs in mm².". Renumber existing sub-paragraph (e) as sub-paragraph (f). 6.7.3.16.1 Amend to read as follows: "6.7.3.16.1 Every portable tank must be fitted with a corrosion resistant metal plate permanently attached to the portable tank in a conspicuous place readily accessible for inspection. When for reasons of portable tank arrangements the plate cannot be permanently attached to the shell, the shell must be marked with at least the information required by the pressure vessel code. As a minimum, at least the following information must be marked on the plate by stamping or by any other similar method: (a) (b) Owner information (i) Owner’s registration number; Manufacturing information (i) Country of manufacture; (ii) Year of manufacture; CONSULTATION DRAFT 145
Page 1 and 2:
Consultation Draft Model Amendment
Page 3 and 4:
Model Amendment Regulations -Transp
Page 5 and 6:
Schedule 1 - Amendments to the Mode
Page 7 and 8:
(b) (c) (a) (b) (c) (d) (e) (f) a r
Page 9 and 10:
"(4) {Subclause} (3) does not apply
Page 11 and 12:
(2) The prime contractor must retai
Page 13 and 14:
(2) The Competent Authority must ha
Page 15 and 16:
4. Goods too dangerous to be transp
Page 17 and 18:
G These entries must be used for cy
Page 19 and 20:
"(d) a Non-Type I Underslung Segreg
Page 21 and 22:
(4) In 5.2.1.8, at the end of note
Page 23 and 24:
1 IBC with ½ size EIP fully visibl
Page 25 and 26:
"10.2.3.7 Despite 10.2.3.1 and 10.2
Page 27 and 28:
Note 2: In cases of combination veh
Page 29 and 30:
UN HAZCHEM HIN UN HAZCHEM HIN UN HA
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
UN HAZCHEM HIN 3272 3YE (3) 33 3Y 3
Page 37 and 38:
Model Amendment Regulations - Trans
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94: Model Amendment Regulations - Trans
Page 129 and 130: Not less than 250 mm Model Amendmen
Page 143: Model Amendment Regulations - Trans
Page 159: Model Amendment Regulations - Trans
show all

Consultation Draft - National Transport Commission

Create successful ePaper yourself

Delete template?

Save as template?