Consultation Draft - National Transport Commission

More documents

Recommendations

Info

Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 Figure 6.7.4.15.1: Example of identification plate marking Owner’s registration number MANUFACTURING INFORMATION Country of manufacture Year of manufacture Manufacturer Manufacturer’s serial number APPROVAL INFORMATION Approval country Authorized body for design approval Design approval number ‘AA’ (if applicable) Shell design code (pressure vessel code) PRESSURES MAWP bar or kPa Test pressure bar or kPa Initial pressure test date: (mm/yyyy) Witness stamp: TEMPERATURES Minimum design temperature °C MATERIALS Shell material(s) and material standard reference(s) Equivalent thickness in reference steel mm CAPACITY Tank water capacity at 20 °C litres INSULATION ‘Thermally insulated’ or ‘Vacuum insulated’ (as applicable) Heat influx Watts HOLDING TIMES Refrigerated liquefied gas(es) permitted Reference holding Degree of Initial pressure time filling days or hours bar or kPa kg PERIODIC INSPECTIONS / TESTS Test type Test date Witness stamp Test type Test date Witness stamp (mm/yyyy) (mm/yyyy) 6.7.4.15.2 Insert "Portable tank instruction in accordance with 4.2.5.2.6" in the list. ". 150 CONSULTATION DRAFT
Model Amendment Regulations – <strong>Transport</strong> of Dangerous Goods by Road or Rail – Package No. 2 6.7.5.4.1 Amend the last sentence to read as follows: "If so required by the competent authority of the country of use, MEGCs for other gases must be fitted with pressure relief devices as specified by that competent authority.". 6.7.5.6.1 After sub-paragraph (c), add the following new sub-paragraph (d): "(d) The cross sectional flow areas of the spring loaded pressurerelief devices and frangible discs in mm².". 6.7.5.13.1 Amend to read as follows: "6.7.5.13.1 Every MEGC must be fitted with a corrosion resistant metal plate permanently attached to the MEGC in a conspicuous place readily accessible for inspection. The metal plate must not be affixed to the elements. The elements must be marked in accordance with Chapter 6.2. As a minimum, at least the following information must be marked on the plate by stamping or by any other similar method: (a) (b) (c) (d) Owner information (i) Owner’s registration number; Manufacturing information (i) (ii) Country of manufacture; Year of manufacture; (iii) Manufacturer’s name or mark; (iv) Manufacturer’s serial number; Approval information (i) The United Nations packaging symbol ; (ii) This symbol must not be used for any purpose other than certifying that a packaging, a portable tank or a MEGC complies with the relevant requirements in Chapter 6.1, 6.2, 6.3, 6.5, 6.6 or 6.7; Approval country; (iii) Authorized body for the design approval; (iv) Design approval number; (v) Pressures Letters ‘AA’, if the design was approved under alternative arrangements (see 6.7.1.2); CONSULTATION DRAFT 151
Page 1 and 2:
Consultation Draft Model Amendment
Page 3 and 4:
Model Amendment Regulations -Transp
Page 5 and 6:
Schedule 1 - Amendments to the Mode
Page 7 and 8:
(b) (c) (a) (b) (c) (d) (e) (f) a r
Page 9 and 10:
"(4) {Subclause} (3) does not apply
Page 11 and 12:
(2) The prime contractor must retai
Page 13 and 14:
(2) The Competent Authority must ha
Page 15 and 16:
4. Goods too dangerous to be transp
Page 17 and 18:
G These entries must be used for cy
Page 19 and 20:
"(d) a Non-Type I Underslung Segreg
Page 21 and 22:
(4) In 5.2.1.8, at the end of note
Page 23 and 24:
1 IBC with ½ size EIP fully visibl
Page 25 and 26:
"10.2.3.7 Despite 10.2.3.1 and 10.2
Page 27 and 28:
Note 2: In cases of combination veh
Page 29 and 30:
UN HAZCHEM HIN UN HAZCHEM HIN UN HA
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
UN HAZCHEM HIN 3272 3YE (3) 33 3Y 3
Page 37 and 38:
Model Amendment Regulations - Trans
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100: Model Amendment Regulations - Trans
Page 129 and 130: Not less than 250 mm Model Amendmen
Page 149: Model Amendment Regulations - Trans
Page 159: Model Amendment Regulations - Trans
show all

Consultation Draft - National Transport Commission

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?