Installation Manual for SMX Modules - OEM Automatic AB

More documents

Recommendations

Info

Installation Manual 10.2.3 Wiring two-channel (same group) EAA1 EAA2 P1 P2 EAA3 EAA4 EAA5 EAA6 X12 X21 EAA7 EAA8 EAA9 EAA10 X22 L+ L- HB-37350-810-01-10E-EN SMX installation manual.doc Page 46 of 46
Installation Manual Response times of the SMX The SMX response times are specified in the following section. 10.3 Response times in standard operation The cycle time of the SMX system serves as basis for calculating the response times. In operation this is T_cycle = 8 ms. The specified response times comply with the corresponding maximum running time for the actual application within the SMX module. Depending on the application, further, application dependent response times of the sensors and actuators used must be added, in order to obtain the total running time. Function Activation of a monitoring function by means of ENABLE with subsequent shut-down via digital output Activation of a monitoring function by means of ENABLE with subsequent shut-down via safety relay Response of an already activated monitoring function including PLC editing in case of position and speed processing via digital output Response of an already activated monitoring function including PLC editing in case of position and speed processing via digital output Activation of digital output via digital input Activation output relay via digital input Deactivation of digital output via digital input Deactivation output relay via digital input Average filter (setting see encoder dialog SafePLC) Response time [ms] 24 *) 47 *) 16 *) 39 *) 16 26 16 47 0 - 64 Explanation Activation of a monitoring function by means of the ENABLE signal. Activation of a monitoring function by means of the ENABLE signal. With a monitoring function that has already been activated via ENABLE, the module requires one cycle to calculate the current speed value. During the next cycle after calculation of the monitoring function the information is further processed and output by the PLC, i.e. according to the implemented logic this will lead to e.g. switching of an output. With a monitoring function that has already been activated via ENABLE, the module requires one cycle to calculate the current speed value. During the next cycle after calculation of the monitoring function the information is further processed and output by the PLC, i.e. according to the implemented logic this will lead to e.g. switching of an output. Activation of an input and switching of the output Activation of an input and switching of the output Deactivation of an input and thus deactivation of the output Deactivation of an input and thus deactivation of the output Group running time of the averager. This running time only effects the monitoring function in connection with position / speed / acceleration, but not the logic processing. HB-37350-810-01-10E-EN SMX installation manual.doc Page 47 of 47
Page 1 and 2: Installation Manual Installation Ma
Page 3 and 4: Installation Manual 9 SAFETY RELEVA
Page 5 and 6: Installation Manual 1.2 Co-valid do
Page 7 and 8: Installation Manual 2 Safety regula
Page 9 and 10: Installation Manual 3.1.2 SMX11 Typ
Page 11 and 12: Installation Manual 3.1.4 SMX12A Ty
Page 13 and 14: Installation Manual 3.1.6 Type plat
Page 15 and 16: Installation Manual 4.2 Installatio
Page 17 and 18: Installation Manual 4.4 External 24
Page 19 and 20: Installation Manual 4.6 Connection
Page 21 and 22: Installation Manual Note: • In th
Page 23 and 24: Installation Manual 2. Single-chann
Page 27 and 28: Installation Manual Attention: The
Page 33 and 34: Installation Manual 8 Sensor type A
Page 35 and 36: Installation Manual For application
Page 37 and 38: Installation Manual The test functi
Page 39 and 40: Installation Manual 10.1.2 Single-p
Page 41 and 42: Installation Manual 10.1.4 Single-p
Page 43 and 44: Installation Manual 10.1.6 Wiring o
Page 45: Installation Manual 10.2.2 Wiring t
Page 49 and 50: Installation Manual 11 Start-up 11.
Page 51 and 52: Installation Manual 11.4 Terminal a
Page 53 and 54: Installation Manual 12 Safety relat
Page 55 and 56: Installation Manual 14 Technical da
Page 57 and 58: Installation Manual 15.2 Alarm list
Page 59 and 60: Installation Manual Alarm code A 30
Page 75 and 76: Installation Manual 15.3 Fatal Erro
Page 77 and 78: Installation Manual Fatal Error Cod
Page 87 and 88: Installation Manual 16 Encoder type
Page 89 and 90: Installation Manual 17 Switch types
Page 91 and 92: Installation Manual Type Graphic sy
Page 93 and 94: Installation Manual 10 eSwitch_3oT
Page 95 and 96: Installation Manual eTwoHand_2s LD
Page 97 and 98:
Installation Manual Two-hand button
show all

Installation Manual for SMX Modules - OEM Automatic AB

Create successful ePaper yourself

Delete template?

Save as template?