Industrial Computing Solutions Fan-less Computer NISE ... - Omtec

More documents

Recommendations

Info

Chapter 2: Jumpers and Connectors Chapter 2: Jumpers and Connectors This chapter describes the jumpers and connectors on the motherboard. Note that the following procedures are generic for all NISE 2100/2110 series. Before You Begin • Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated. • Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: • A Philips screwdriver • A flat-tipped screwdriver • A set of jewelers Screwdrivers • A grounding strap • An anti-static pad • Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors. • Before working on internal components, make sure that the power is off. Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic components. Humid environment tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists. Precautions Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on the computers that are still connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to your computer or yourself: • Always disconnect the unit from the power outlet whenever you are working inside the case. • If possible, wear a grounded wrist strap when you are working inside the computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance. • Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it is necessary to do so. Don’t flex or stress the circuit board. • Leave all components inside the static-proof packaging that they shipped with until they are ready for installation. • Use correct screws and do not over tighten screws. Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 13 NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 2: Jumpers and Connectors Jumper Settings A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open. Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right) Three-Pin Jumpers: Pins 1 and 2 Are Short Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 14 NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Page 1 and 2: NEXCOM International Co., Ltd. Indu
Page 3 and 4: Contents COM1 and COM2 Ports.......
Page 5 and 6: Preface RoHS Compliance NEXCOM RoHS
Page 7 and 8: Preface Warnings Read and adhere to
Page 9 and 10: Preface Technical Support and Assis
Page 11 and 12: Preface China-Beijing Room 301, Blo
Page 13 and 14: Preface Ordering Information The fo
Page 15 and 16: Chapter 1: Product Introduction NIS
Page 17 and 18: Chapter 1: Product Introduction Env
Page 25: Chapter 1: Product Introduction NIS
Page 29 and 30: Chapter 2: Jumpers and Connectors T
Page 31 and 32: Chapter 2: Jumpers and Connectors P
Page 33 and 34: Chapter 2: Jumpers and Connectors C
Page 35 and 36: Chapter 2: Jumpers and Connectors E
Page 37 and 38: Chapter 2: Jumpers and Connectors L
Page 39 and 40: Chapter 2: Jumpers and Connectors C
Page 41 and 42: Chapter 2: Jumpers and Connectors I
Page 43 and 44: Chapter 2: Jumpers and Connectors I
Page 45 and 46: Chapter 2: Jumpers and Connectors L
Page 47 and 48: Chapter 2: Jumpers and Connectors M
Page 49 and 50: Chapter 3: System Setup Chapter 3:
Page 51 and 52: Chapter 3: System Setup 3. Push the
Page 53 and 54: Chapter 3: System Setup 3. Push the
Page 55 and 56: Chapter 3: System Setup 3. Noticeab
Page 57 and 58: Chapter 3: System Setup Installing
Page 59 and 60: Chapter 3: System Setup 5. Turn to
Page 61 and 62: Chapter 3: System Setup Installing
Page 63 and 64: Chapter 3: System Setup 3. Remove t
Page 65 and 66: Chapter 4: BIOS Setup Chapter 4: BI
Page 67 and 68: Chapter 4: BIOS Setup BIOS Setup Ut
Page 69 and 70: Chapter 4: BIOS Setup IDE Configura
Page 71 and 72: Chapter 4: BIOS Setup Super IO Conf
Page 73 and 74: Chapter 4: BIOS Setup Hardware Heal
Page 75 and 76: Chapter 4: BIOS Setup Bootup Num-Lo
Page 77 and 78:
Chapter 4: BIOS Setup DVMT Mode Sel
Page 79 and 80:
Chapter 4: BIOS Setup PCIPnP This s
Page 81 and 82:
Chapter 4: BIOS Setup Exit Discard
Page 83 and 84:
Appendix A: Power Consumption Power
Page 85 and 86:
Appendix B: GPI/O Programming Guide
Page 87:
Appendix C: Watchdog Timer Setting
show all

Industrial Computing Solutions Fan-less Computer NISE ... - Omtec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?