Industrial Computing Solutions Fan-less Computer NISE ... - Omtec

More documents

Recommendations

Info

Appendix B: GPI/O Programming Guide Appendix B: GPI/O Programming guide GPI/O (General Purpose Input/Output) pins are provided for custom system design. This appendix provides definitions and its default setting for the ten GPI/O pins in the NISE 2100/2110 Series. The pin definition is shown in the following table: Pin GPI/O Mode Power On Default Address Pin GPI/O Mode Power On Default Address 1 VCC - - 2 GND - - 3 GPO Low 284h (Bit4) 4 GPI High 284h (Bit0) 5 GPO Low 284h (Bit5) 6 GPI High 284h (Bit1) 7 GPO Low 284h (Bit6) 8 GPI High 284h (Bit2) 9 GPO Low 284h (Bit7) 10 GPI High 284h (Bit3) J8 - GPI/O connector Control the GPO pin (3/5/7/9) level from I/O port 284h bit (4/5/6/7). The bit Set/Clear indicated output High/Low. GPIO Programming Sample Code #define GPIO_PORT 0x284 #define GPO3 (0x01
Appendix B: GPI/O Programming Guide { GPO3_HI; GPO5_LO; GPO7_HI; GPO9_LO; } Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 72 NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Page 1 and 2:
NEXCOM International Co., Ltd. Indu
Page 3 and 4:
Contents COM1 and COM2 Ports.......
Page 5 and 6:
Preface RoHS Compliance NEXCOM RoHS
Page 7 and 8:
Preface Warnings Read and adhere to
Page 9 and 10:
Preface Technical Support and Assis
Page 11 and 12:
Preface China-Beijing Room 301, Blo
Page 13 and 14:
Preface Ordering Information The fo
Page 15 and 16:
Chapter 1: Product Introduction NIS
Page 17 and 18:
Chapter 1: Product Introduction Env
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Chapter 2: Jumpers and Connectors J
Page 29 and 30:
Chapter 2: Jumpers and Connectors T
Page 31 and 32:
Chapter 2: Jumpers and Connectors P
Page 33 and 34: Chapter 2: Jumpers and Connectors C
Page 35 and 36: Chapter 2: Jumpers and Connectors E
Page 37 and 38: Chapter 2: Jumpers and Connectors L
Page 39 and 40: Chapter 2: Jumpers and Connectors C
Page 41 and 42: Chapter 2: Jumpers and Connectors I
Page 43 and 44: Chapter 2: Jumpers and Connectors I
Page 45 and 46: Chapter 2: Jumpers and Connectors L
Page 47 and 48: Chapter 2: Jumpers and Connectors M
Page 49 and 50: Chapter 3: System Setup Chapter 3:
Page 51 and 52: Chapter 3: System Setup 3. Push the
Page 53 and 54: Chapter 3: System Setup 3. Push the
Page 55 and 56: Chapter 3: System Setup 3. Noticeab
Page 57 and 58: Chapter 3: System Setup Installing
Page 59 and 60: Chapter 3: System Setup 5. Turn to
Page 61 and 62: Chapter 3: System Setup Installing
Page 63 and 64: Chapter 3: System Setup 3. Remove t
Page 65 and 66: Chapter 4: BIOS Setup Chapter 4: BI
Page 67 and 68: Chapter 4: BIOS Setup BIOS Setup Ut
Page 69 and 70: Chapter 4: BIOS Setup IDE Configura
Page 71 and 72: Chapter 4: BIOS Setup Super IO Conf
Page 73 and 74: Chapter 4: BIOS Setup Hardware Heal
Page 75 and 76: Chapter 4: BIOS Setup Bootup Num-Lo
Page 77 and 78: Chapter 4: BIOS Setup DVMT Mode Sel
Page 79 and 80: Chapter 4: BIOS Setup PCIPnP This s
Page 81 and 82: Chapter 4: BIOS Setup Exit Discard
Page 83: Appendix A: Power Consumption Power
Page 87: Appendix C: Watchdog Timer Setting
show all

Industrial Computing Solutions Fan-less Computer NISE ... - Omtec

Create successful ePaper yourself

Delete template?

Save as template?