GRAIN DRYER & PARTS BOOK - Opico

More documents

Recommendations

Info

TERMINAL BLOCK KEY RAB 1. Flame Detector (N.O.) - Black 22 High Limit Switch - White/Black 2. Low Heat Solenoid - Black 23. Relay Panel #1 - Green 3. High Heat Solenoid - Black 24. Full Switch - Brown 4. Agitator Sensor - White/Blue 25. Empty Switch - Brown 5. Plenum Tem. Sensor - White/Orange 26. Fuse - 7 AMP 6. Grain Temp. Sensor - White/Orange 27. 12 VDC Positive - Yellow 7. Plenum Temp. Sensor - White/Black 28. 12 VDC Negative - Brown 8. Grain Temp. sensor - White/Black 29. Auger Sensor - Yellow 9. Auger Sensor - Brown 30. Full Sensor - Blue 10. Full Sensor - Black 31. Earth Ground - Green 11. Empty Sensor - Black 32. Empty Sensor - Blue 12. Liquid Solenoid - Black 33. Agitator Sensor - White/Black 13. Liquid Solenoid - Black 34. High Limit Switch - Orange 14. Relay Panel #6 - Red (Auger Control) 35. Air Switch (N.O.) - Black 15. Relay Panel #5 - White (Fan Control) 36. Open Terminal 16. Relay Panel #4 - Brown (Load Control) 37. Liquid Solenoid - Blue 17. Relay Panel #3 - Yellow (Unload Control) 38. Liquid Solenoid - Blue 18. Ignition Coil (Neg.) - White 39. Fuse - 7 AMP 19. Low Heat Solenoid - Blue 40. Flame Detector (Common) - White 20. High Heat Solenoid - Blue 41. Ignition Coil (Pos.) - Black 21. Air Switch (Common) - White MICROPROCESSOR CABLE BK - Black (Ground) BL - Blue (Liq. Sol.) BN - Brown (Ignition) GN - Green (Agitator) GY - Gray (Common) GY/BN - Gray/Brown (Common) O - Orange (Low Sol.) R - Red (12 VDC Power) BLK/R - Black/Red (Sol. Com.) R/GN - Red/Green (Empty) R/Y - Red/Yellow (Air/High Lim.) T - Tan (Full) V - Violet (Auger) W - White (Flame) W/BK - white/Black (Plenum) W/BL - White/Blue (Load Motor) W/BN - White/Brown (Auger Motor) W/GN - White/Green (Unload Mtr.) W/O - White/Orange (Plenum) W/GY - White/Gray (Com.) W/V - White/Violet (Fan Motor) W/Y - White/Yellow (Grain Temp.) Y - Yellow (High Heat Sol.) 42
ELECTRICAL CONTROL BOX WIRING DIAGRAM RAB 3 PHASE 43
Page 1 and 2: RAB RECIRCULATING AUTOMATIC BATCH G
Page 3 and 4: MANUFACTURERS OF FARM AND INDUSTRIA
Page 6: BE A SAFE OPERATOR BY THINKING - BE
Page 10 and 11: GENERAL INFORMATION Mechanical dryi
Page 12 and 13: 1. INSTALLATION OF EQUIPMENT INSTAL
Page 14 and 15: 8. LUBRICATION Use a high-low tempe
Page 16 and 17: CONTROLS IDENTIFICATION Do not oper
Page 18 and 19: DANGER The loading auger operates a
Page 20 and 21: The two drying options are Automati
Page 22 and 23: Grain Parameter Setting - The first
Page 24 and 25: Detailed Controller Operation Assum
Page 26 and 27: Figure 4AC - The MENU key will acti
Page 28 and 29: desired value is reached. One depre
Page 30 and 31: Fill and Unload Options - If both d
Page 32 and 33: and the grain cool-down setpoint. s
Page 34 and 35: Regardless of the state of the moto
Page 36 and 37: Figure 5B - Entry path to Clock set
Page 38 and 39: 2. Return to Idle - The controller
Page 40 and 41: 6. 7. 38
Page 42 and 43: 40 SENSOR LOCATIONS
Page 46 and 47: page 12. (See page 11) page 41, 44
Page 49: See page 36 15. If flame sensor is
Page 52 and 53: See wiring diagram on page 43. 4. I
Page 54 and 55: 52 POWER FRAME ASSEMBLY THREE PHASE
Page 56 and 57: 54 POWER FRAME ASSEMBLY THREE PHASE
Page 58 and 59: 56 BURNER ASSEMBLY THREE PHASE
Page 60 and 61: 58 PROPANE CONTROL CABINET ASSEMBLY
Page 62 and 63: PROPANE CONTROL CABINET ASSEMBLY TH
Page 64 and 65: 62 FRAME ASSEMBLY THREE PHASE
Page 66 and 67: 64 AGITATOR ASSEMBLY THREE PHASE
Page 68 and 69: 66 AGITATOR DRIVE ASSEMBLY THREE PH
Page 70 and 71: 68 PLENUM ASSEMBLY THREE PHASE
Page 72 and 73: 70 AUGER ASSEMBLY THREE PHASE
Page 74 and 75: 72 VERTICAL AUGER DRIVE ASSEMBLY TH
Page 76 and 77: 74 OUTSIDE SKIN ASSEMBLY THREE PHAS
Page 78 and 79: 76 LARGE PLENUM OUTSIDE SKIN AND EX
Page 80: LOADING HOPPER (STANDARD) THREE PHA
Page 83 and 84: 9' HOPPER PARTS LIST 71992 Capscrew
Page 85 and 86: LOADING AUGER DRIVE ASSEMBLY THREE
Page 87 and 88: ELECTRICAL CONTROL BOX ASSEMBLY THR
Page 89: NATURAL GAS CONTROL CABINET ASSEMBL

GRAIN DRYER & PARTS BOOK - Opico

Create successful ePaper yourself

Delete template?

Save as template?