User Manual - Barco

More documents

Recommendations

Info

Connecting the signal cables TO CONNECT THE SIGNAL CABLES TO THE DISPLAY: To get access to the connectors, remove the connector compartment cover by pulling down the 2 clips at the top of the cover. The location of the connectors depends on the display type: 1 2 3 4 Figure 10: Inputs E-3620, MDNG-5121 4 1 2 3 Figure 11: Inputs MDNC-3121, MDNG-2121 and MDNG-6121 1 2 3 4 Figure 12: Inputs MDNC-2121 • Connect one end of the DVI/DisplayPort cable to the DVI/ DisplayPort input of the display (1). Connect the other end of the DVI/DisplayPort cable to the DVI/DisplayPort connector of the display controller board. • Connect a PC USB downstream connector to the display’s USB upstream connector by means of a USB cable (2). • Connect any USB device to one of the display’s USB downstream connectors (3) • Connect the DC power input (4) of the display to the external DC power supply. Connect the other end of the external DC power supply to a grounded power outlet by means of the proper power cord delivered in the packaging. 16 Nio
Routing the cables • Bind the cables in the connector compartment together with the cable tie inside the connector compartment. • Put the connector compartment cover back on the display. Pay attention that the signal cables are positioned under the bulge in the cover. • Push the cables into the clips on the rear of the tilt & swivel foot. • Bind the cables together above and under the foot, by means of the 2 velcro strips attached to the inside of the foot cover (packed inside the accessory box). • At last, put the foot cover back in place. Re-attaching the covers (2) Figure 13: Installing the cover 1 The foot cover is packaged separately in the accessory box. Unpack the foot cover. 2 Push the upper side of the cover onto the foot, so that the hooks inside the cover are positioned right under the bulges at the rear of the foot. Nio 17
Page 1 and 2: Nio User Guide Supported displays:
Page 3 and 4: Welcome! Nio is Barco's flexible, i
Page 5 and 6: Table of contents What's in the box
Page 7 and 8: What's in the box Your BARCO NIO Di
Page 9 and 10: Rear view REAR VIEW OF E-3620, MDNG
Page 11 and 12: REAR VIEW OF MDNC-2121 1 2 4 5 6 7
Page 13 and 14: Adjusting the display position You
Page 15: 3 To change from portrait to landsc
Page 19 and 20: 3 Remove the small screw (A) fixing
Page 21 and 22: performance of the product. To ensu
Page 23 and 24: 4 The LED turns orange. BARCO Push
Page 25 and 26: TO ENABLE USER CONTROLS: 1 Make sur
Page 27 and 28: Changing values in the OSD menus 1
Page 29 and 30: Luminance and color menu In graysca
Page 31 and 32: ALC & DICOM OPTIONS SUBMENU* Correc
Page 33 and 34: Settings menu DPMS Power LED User c
Page 35 and 36: Changing Display Functions Concepts
Page 37 and 38: User This is a user-definable DF. U
Page 39 and 40: CT/MR/NM Office Clinical Emergency
Page 41 and 42: Cleaning your display Front glass C
Page 43 and 44: Important information Safety inform
Page 45 and 46: WATER AND MOISTURE Never expose the
Page 47 and 48: 中国大陆 ROHS (CHINESE MAINL
Page 49 and 50: Regulatory compliance information I
Page 51 and 52: Indicates the USB connectors on the
Page 53 and 54: Technical specifications NIO 2MP Pr
Page 55 and 56: Swivel -45° / +45° Pivot 90° Mou
Page 57 and 58: Housing color Video input signals U
Page 59 and 60: NIO 5MP Product acronym Screen tech
Page 61 and 62: Mounting standard Screen protection
Page 63 and 64: Video input signals USB ports DVI-D
Page 65: NIO 5MP Product acronym Screen tech
Page 68 and 69:
NIO COLOR 2MP HB Product acronym Sc
Page 70 and 71:
Screen protection Recommended modal
Page 72 and 73:
Products have not been installed by
Page 74 and 75:
expression "force majeure" means, b
Page 76:
B410582-08 March 2012 0120 Barco n.
show all

User Manual - Barco

Create successful ePaper yourself

Delete template?

Save as template?