Shark 200S User Manual - MicroDAQ.com

More documents

Recommendations

Info

11. Service: Current Only Measurement (Single Phase) A N Wireless Ethernet Connection Ia Electronic Circuits Ethernet, RJ-45 Jack Ia Ia Ib Ib Ic Ic (+) (-) (+) (-) (+) (-) Va Vb Vc Vref L1 L2 PE Z K Y A B SH (+)(-) RS-485 KYZ Pulse Output 20VAC Minimum* Power Supply Inputs A N Select: “3 EL WYE” (3 Element Wye) in Meter Programming setup. * For improved accuracy, this connection is recommended, but not required. E Electro Industries/GaugeTech Doc# E149721 4-14
Chapter 5 Communication Installation 5.1: Shark® 200-S Meter Communication The Shark® 200-S submeter provides two independent Communication ports plus KYZ pulse output. (For information on Ethernet configuration, see Chapter 6.) The first port, Com 1, is an IrDA Port, which uses Modbus ASCII. The second port, Com 2, provides RS485 or RJ45 Ethernet or Wi-Fi Ethernet Communication. 5.1.1: IrDA Port (Com 1) The Shark® 200-S submeter’s Com 1 IrDA port is located on the meter’s face. This port allows the unit to be set up and programmed with any device capable of IrDA communication, including a PDA with CoPilot EXT software, some laptops and USB/IrDA wands (such as the USB to IrDA Adapter [CAB6490] described in Appendix E). Just point at the meter with an IrDA-equipped PC, PDA, or adapter and configure it. CoPilot EXT is a Windows® based Mobile software package for a PDA that allows it to communicate with the Shark® meter to configure settings and poll readings. Refer to the Communicator EXT User’s Manual for details on programming the meter and accessing readings. IrDA Port Settings are: Address: 1 Baud Rate: 57.6k Protocol: Modbus ASCII Figure 5.1: Communication with IrDA Port E Electro Industries/GaugeTech Doc # E149721 5-1
Page 1 and 2: Shark ® 200-S Electronic Submeter
Page 3 and 4: Shark® 200-S Submeter User Manual
Page 5 and 6: About Electro Industries/GaugeTech
Page 7 and 8: Table of Contents EIG Warranty ii C
Page 9 and 10: B.5: Retrieving Logs Using the Modb
Page 11 and 12: Chapter 1 Three-Phase Power Measure
Page 13 and 14: 1.1.2: Delta Connection Delta conn
Page 15 and 16: single three-phase reading. Some di
Page 17 and 18: Time Interval (Minute) Power (kW) E
Page 19 and 20: I R V I X I Angle θ Figure 1.9: Vo
Page 21 and 22: Total A Phase Current with Harmonic
Page 23 and 24: 1.5: Power Quality Power quality c
Page 25 and 26: Chapter 2 Shark ® 200-S Submeter O
Page 27 and 28: 2.1.3: Measured Values The Shark ®
Page 29 and 30: Environmental Rating • Storage: (
Page 31 and 32: Chapter 3 Mechanical Installation 3
Page 33 and 34: 3.3: Secure the Cover 1. Close the
Page 35 and 36: Chapter 4 Electrical Installation 4
Page 37 and 38: 4.5: Electrical Connection Diagrams
Page 39 and 40: 2. Service: 2.5 Element WYE, 4-Wire
Page 41 and 42: 4. Service: 2.5 Element WYE, 4-Wire
Page 43 and 44: 6. Service: Delta, 3-Wire with No P
Page 45 and 46: 8. Service: Delta, 3-Wire with 2 PT
Page 47: 10. Service: Current Only Measureme
Page 51 and 52: 5.1.2: RS485 Communication Com 2 (4
Page 53 and 54: 5.1.4: Ethernet Connection In order
Page 55 and 56: The Communicator EXT Main screen re
Page 57 and 58: Energy, Power Scaling, and Averagin
Page 59 and 60: Chapter 6 Ethernet Connection Confi
Page 61 and 62: 4. You will see the window shown on
Page 63 and 64: 1) Network/IP Settings: Network Mod
Page 65 and 66: 6.4: Network Module Hardware Initia
Page 67 and 68: Chapter 7 Using the Shark ® 200-S
Page 69 and 70: 7.2.2: Using the Main Menu 1. Press
Page 71 and 72: 7.2.5: Using Configuration Mode Con
Page 73 and 74: 7.2.5.2: Configuring CT Setting The
Page 75 and 76: 7.2.5.4: Configuring Connection Set
Page 77 and 78: Operating Mode Parameter Readings:
Page 79 and 80: Figure 7.3: Using the Watt-Hour Tes
Page 81 and 82: Appendix A Navigation Maps for the
Page 83 and 84: Operating Mode Screens RIGHT See No
Page 85 and 86: Configuration Mode Screens See Note
Page 87 and 88: Appendix B Modbus Mapping and Log R
Page 89 and 90: B.5: Retrieving Logs Using the Shar
Page 91 and 92: etween Historical Logs 1, 2, and 3.
Page 93 and 94: 2) Log Status Block: The Log Status
Page 95 and 96: • Enable: This value sets if a lo
Page 97 and 98: Starting Address Hi C3 Starting Add
Page 99 and 100:
• Space in the window after the l
Page 101 and 102:
4) Compute #RecPerWin as (246\18)=1
Page 103 and 104:
10) If number records - current ind
Page 105 and 106:
Group (Event group) Event (Event wi
Page 107 and 108:
send: :01 03 C7 57 00 10 - Historic
Page 109 and 110:
Modbus Address Fixed Data Section I
Page 111 and 112:
Primary Demand Block read-only Hex
Page 113 and 114:
Phase Angle Block read-only Hex Dec
Page 115 and 116:
Primary Minimum Timestamp Block rea
Page 117 and 118:
Primary Maximum Timestamp Block rea
Page 119 and 120:
Programmable Settings Section Basic
Page 121 and 122:
12-Bit Readings Section 12-Bit Bloc
Page 123 and 124:
Data Formats ASCII ASCII characters
Page 125 and 126:
Appendix C Using DNP Mapping for th
Page 127 and 128:
C.6: DNP Lite Register Map Object 1
Page 129 and 130:
Object 80 - Internal Indicator Obje
Page 131 and 132:
Reset Energy Request 05 64 18 C4 ds
Page 133 and 134:
Appendix D Using the USB to IrDA Ad
Page 135 and 136:
8. You do not need to be concerned
Page 137 and 138:
This time, click the Radio Button n
Page 139 and 140:
Click Finish to close the Found New
show all

Shark 200S User Manual - MicroDAQ.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?