Shark 200S User Manual - MicroDAQ.com

More documents

Recommendations

Info

Chapter 6: Ethernet Connection Configuration 6.1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 6.2: Setting up the Host PC to Communicate with Shark® 200-S meter . . . . . . 6-1 6.2:1 Configuring the Host PC’s Ethernet Adapter Using Windows XP . . . . . . . 6-2 6.3.: Setting up the Ethernet Module in the Shark® 200-S Meter . . . . . . . . . . 6-3 6.3.1: Configuring the Ethernet Module on the Host PC using Windows XP . . . . . 6-4 6.3.2: Example of Modifying Parameters in Groups 1 and 6 . . . . . . . . . . . . 6-6 6.4.: Network Module Hardware Initialization . . . . . . . . . . . . . . . . . . 6-7 Chapter 7: Using the Submeter 7.1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 7.1.1: Submeter Face Elements . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 7.1.2: Submeter Face Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 7.2: % of Load Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 7.3: Watt-Hour Accuracy Testing (Verification) . . . . . . . . . . . . . . . . . 7-3 7.3.1: KYZ Pulse Constants . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 7.4: Upgrade the Submeter Using V-Switches . . . . . . . . . . . . . . . . . . 7-4 Chapter 8: Configuring the Submeter Using the Front Panel 8.1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 8.2: Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 8.3: Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8.3.1: Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8.3.2: Reset Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8.3.2.1: Enter Password (ONLY IF ENABLED IN SOFTWARE) . . . . . . . . . . 8-3 8.3.3: Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 8.3.3.1: Configure Scroll Feature . . . . . . . . . . . . . . . . . . . . . . . . 8-4 8.3.3.2: Program Configuration Mode Screens . . . . . . . . . . . . . . . . . . 8-5 8.3.3.3: Configure CT Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 8.3.3.4: Configure PT Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 8.3.3.5: Configure Connection (Cnct) Setting . . . . . . . . . . . . . . . . . . . 8-8 8.3.3.6: Configure Communication Port Setting . . . . . . . . . . . . . . . . . . 8-9 8.3.4: Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Appendix A: Shark® 200-S Submeter Navigation Maps A.1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 A.2: Navigation Maps (Sheets 1 to 4) . . . . . . . . . . . . . . . . . . . . . . A-1 Main Menu Screens (Sheet 1) Operating Mode Screens (Sheet 2) Reset Mode Screens (Sheet 3) Configuration Mode Screens (Sheet 4) Appendix B: Modbus Mapping for the Shark® 200-S Submeter B.1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 B.2: Modbus Register Map Sections . . . . . . . . . . . . . . . . . . . . . . . B-1 B.3: Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 B.4: Floating Point Values . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 e Electro Industries/GaugeTech Doc # E149721 vi
B.5: Retrieving Logs Using the Modbus Map . . . . . . . . . . . . . . . . . . B-3 B.5.1: Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 B.5.2: Meter Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 B.5.3: Block Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 B.5.4: Log Retrieval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 B.5.4.1: Auto-Increment . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 B.5.4.2: Modbus Function Code 0x23 . . . . . . . . . . . . . . . . . . . . . B-10 B.5.4.3: Log Retrieval Procedure . . . . . . . . . . . . . . . . . . . . . . . B-12 B.5.4.4: Log Retrieval Example . . . . . . . . . . . . . . . . . . . . . . . B-13 B.5.5: Log Record Interpretation . . . . . . . . . . . . . . . . . . . . . . . B-18 B.6: Modbus Map Registers(MM-1 to MM-26) . . . . . . . . . . . . . . . . . B-23 Appendix C: Using the DNP Mapping for Shark® 200-S Submeter C.1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 C.2: Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 C.3: Data Link Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 C.4: Application Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 C.5: Error Reply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 C.6: DNP Lite Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 C.7: DNP Message Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 Appendix D: Using the USB to IrDA Adapter (CAB6490) D.1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1 D.2: Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . D-1 e Electro Industries/GaugeTech Doc # E149721 vii
Page 1 and 2: Shark ® 200-S Electronic Submeter
Page 3 and 4: Shark® 200-S Submeter User Manual
Page 5 and 6: About Electro Industries/GaugeTech
Page 7: Table of Contents EIG Warranty ii C
Page 11 and 12: Chapter 1 Three-Phase Power Measure
Page 13 and 14: 1.1.2: Delta Connection Delta conn
Page 15 and 16: single three-phase reading. Some di
Page 17 and 18: Time Interval (Minute) Power (kW) E
Page 19 and 20: I R V I X I Angle θ Figure 1.9: Vo
Page 21 and 22: Total A Phase Current with Harmonic
Page 23 and 24: 1.5: Power Quality Power quality c
Page 25 and 26: Chapter 2 Shark ® 200-S Submeter O
Page 27 and 28: 2.1.3: Measured Values The Shark ®
Page 29 and 30: Environmental Rating • Storage: (
Page 31 and 32: Chapter 3 Mechanical Installation 3
Page 33 and 34: 3.3: Secure the Cover 1. Close the
Page 35 and 36: Chapter 4 Electrical Installation 4
Page 37 and 38: 4.5: Electrical Connection Diagrams
Page 39 and 40: 2. Service: 2.5 Element WYE, 4-Wire
Page 41 and 42: 4. Service: 2.5 Element WYE, 4-Wire
Page 43 and 44: 6. Service: Delta, 3-Wire with No P
Page 45 and 46: 8. Service: Delta, 3-Wire with 2 PT
Page 47 and 48: 10. Service: Current Only Measureme
Page 49 and 50: Chapter 5 Communication Installatio
Page 51 and 52: 5.1.2: RS485 Communication Com 2 (4
Page 53 and 54: 5.1.4: Ethernet Connection In order
Page 55 and 56: The Communicator EXT Main screen re
Page 57 and 58: Energy, Power Scaling, and Averagin
Page 59 and 60:
Chapter 6 Ethernet Connection Confi
Page 61 and 62:
4. You will see the window shown on
Page 63 and 64:
1) Network/IP Settings: Network Mod
Page 65 and 66:
6.4: Network Module Hardware Initia
Page 67 and 68:
Chapter 7 Using the Shark ® 200-S
Page 69 and 70:
7.2.2: Using the Main Menu 1. Press
Page 71 and 72:
7.2.5: Using Configuration Mode Con
Page 73 and 74:
7.2.5.2: Configuring CT Setting The
Page 75 and 76:
7.2.5.4: Configuring Connection Set
Page 77 and 78:
Operating Mode Parameter Readings:
Page 79 and 80:
Figure 7.3: Using the Watt-Hour Tes
Page 81 and 82:
Appendix A Navigation Maps for the
Page 83 and 84:
Operating Mode Screens RIGHT See No
Page 85 and 86:
Configuration Mode Screens See Note
Page 87 and 88:
Appendix B Modbus Mapping and Log R
Page 89 and 90:
B.5: Retrieving Logs Using the Shar
Page 91 and 92:
etween Historical Logs 1, 2, and 3.
Page 93 and 94:
2) Log Status Block: The Log Status
Page 95 and 96:
• Enable: This value sets if a lo
Page 97 and 98:
Starting Address Hi C3 Starting Add
Page 99 and 100:
• Space in the window after the l
Page 101 and 102:
4) Compute #RecPerWin as (246\18)=1
Page 103 and 104:
10) If number records - current ind
Page 105 and 106:
Group (Event group) Event (Event wi
Page 107 and 108:
send: :01 03 C7 57 00 10 - Historic
Page 109 and 110:
Modbus Address Fixed Data Section I
Page 111 and 112:
Primary Demand Block read-only Hex
Page 113 and 114:
Phase Angle Block read-only Hex Dec
Page 115 and 116:
Primary Minimum Timestamp Block rea
Page 117 and 118:
Primary Maximum Timestamp Block rea
Page 119 and 120:
Programmable Settings Section Basic
Page 121 and 122:
12-Bit Readings Section 12-Bit Bloc
Page 123 and 124:
Data Formats ASCII ASCII characters
Page 125 and 126:
Appendix C Using DNP Mapping for th
Page 127 and 128:
C.6: DNP Lite Register Map Object 1
Page 129 and 130:
Object 80 - Internal Indicator Obje
Page 131 and 132:
Reset Energy Request 05 64 18 C4 ds
Page 133 and 134:
Appendix D Using the USB to IrDA Ad
Page 135 and 136:
8. You do not need to be concerned
Page 137 and 138:
This time, click the Radio Button n
Page 139 and 140:
Click Finish to close the Found New
show all

Shark 200S User Manual - MicroDAQ.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?