YBA250 Antenna and Transmission Line Analyzer User Manual

More documents

Recommendations

Info

Getting Started 2. Rotate the battery retainer upward 1. Push the battery retainer tab down and towards the back of instrument, then lift Figure 1- 9: Opening the battery retainer Lift battery by strap Battery retainer in open position Figure 1- 10: Installing/removing a battery 1-8 YBA250 Antenna and Transmission Line Analyzer User Manual
Getting Started NOTE. The battery electrical contacts, on the bottom of the battery, must face in the direction shown in Figure 1-10. Close and latch the battery retainer and battery compartment door after installing or removing batteries. You can add a second battery to increase the operating time. Replace a battery with the specified type only. To purchase a battery from Tektronix, please contact your Tektronix Service Center for the correct part number. Charging a Battery To charge batteries installed in the NetTek Analyzer Platform, connect the instrument to an external power supply (see Figure 1-7 on page 1-6) and let the battery or batteries recharge in the instrument. Table 1-1 lists the approximate charge times for fully-discharged batteries. You can also charge batteries in the optional external battery charger. Table 1- 1: Approximate battery charge times Number of batteries in instrument Instrument powered on 1 8 hours 3 hours 2 16 hours 6 hours Instrument powered off NOTE. To achieve optimum performance from a new battery, fully charge the battery. Then fully discharge the battery by leaving the YBA250 running (see Start > Help > Settings > Power Management for information on disabling the power saver function), then fully charge the battery again. YBA250 Antenna and Transmission Line Analyzer User Manual 1-9
Page 1 and 2: User Manual YBA250 Antenna and Tran
Page 3: WARRANTY Tektronix warrants that th
Page 6 and 7: Table of Contents Reference Measure
Page 8 and 9: Table of Contents Appendix D: Upgra
Page 10 and 11: Table of Contents Figure 2-11: Read
Page 12 and 13: Table of Contents Tables Table i: S
Page 14 and 15: Table of Contents x YBA250 Antenna
Page 16 and 17: Preface User-defined calibration
Page 18 and 19: Preface Additional Information The
Page 20 and 21: Preface xvi YBA250 Antenna and Tran
Page 22 and 23: General Safety Summary Safety Terms
Page 25 and 26: Getting Started This section descri
Page 27 and 28: Getting Started 1 2 3 4 5 6 7 Figur
Page 29 and 30: Getting Started Attach bus cover Ti
Page 31: Getting Started Batteries Installin
Page 35 and 36: Getting Started Powering On the Ins
Page 37 and 38: Getting Started Shutdown Mode To co
Page 39 and 40: Getting Started Use your own good
Page 41 and 42: Getting Started To install the tilt
Page 43: Operating Basics
Page 46 and 47: Operating Basics Icons Double-tap d
Page 48 and 49: Operating Basics Getting Help To op
Page 50 and 51: Operating Basics Setting the YBA250
Page 52 and 53: Operating Basics Command Bar Area T
Page 54 and 55: Operating Basics Table 2- 4: Tuning
Page 56 and 57: Operating Basics Instrument Area Ic
Page 58 and 59: Operating Basics Table 2- 7: The Fi
Page 60 and 61: Operating Basics Table 2- 10: The T
Page 62 and 63: Operating Basics 2-18 YBA250 Antenn
Page 64 and 65: Connecting a Signal The second type
Page 66 and 67: Connecting a Signal Figure 2- 6: TE
Page 68 and 69: Measurement Overview Two-port inser
Page 70 and 71: Calibration and Normalization When
Page 72 and 73: Calibration and Normalization What
Page 74 and 75: Calibration and Normalization 3. Ca
Page 76 and 77: Calibration and Normalization Figur
Page 78 and 79: Calibration and Normalization Savin
Page 80 and 81: Calibration and Normalization Using
Page 82 and 83:
Calibration and Normalization Table
Page 84 and 85:
Calibration and Normalization Norma
Page 86 and 87:
Calibration and Normalization Table
Page 88 and 89:
Calibration and Normalization UnNor
Page 90 and 91:
Calibration and Normalization 7. Ta
Page 92 and 93:
Calibration and Normalization 3. Ta
Page 94 and 95:
Calibration and Normalization Norma
Page 96 and 97:
Calibration and Normalization 2-52
Page 98 and 99:
Configuring the Instrument 3. To en
Page 100 and 101:
Configuring the Instrument Setting
Page 102 and 103:
Configuring the Instrument 3. To di
Page 104 and 105:
Configuring the Instrument NOTE. Th
Page 106 and 107:
Configuring the Instrument Connecti
Page 108 and 109:
Configuring the Instrument 2-64 YBA
Page 111 and 112:
Setting the Signal Standards and Te
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Measuring Return Loss and VSWR The
Page 119 and 120:
Measuring Return Loss and VSWR If
Page 121 and 122:
Measuring Return Loss and VSWR Meas
Page 123 and 124:
Measuring the Distance to a Fault T
Page 125 and 126:
Measuring the Distance to a Fault F
Page 127 and 128:
Measuring the Distance to a Fault T
Page 129 and 130:
Measuring the Distance to a Fault C
Page 131 and 132:
Measuring the Distance to a Fault C
Page 133 and 134:
Measuring the Distance to a Fault R
Page 135 and 136:
Measuring Insertion Gain and Loss T
Page 137 and 138:
MeasuringInsertionGainandLoss To me
Page 139 and 140:
MeasuringInsertionGainandLoss Requi
Page 141 and 142:
Generating a Continuous Wave (CW) S
Page 143 and 144:
Working with Traces The YBA250 enab
Page 145 and 146:
Working with Traces You can also se
Page 147 and 148:
Working with Traces To save a trace
Page 149 and 150:
Working with Traces Figure 3- 19: D
Page 151 and 152:
Working with Traces Figure 3- 21: S
Page 153 and 154:
Using Markers and Band Edge Cursors
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Mask Testing Mask testing is used t
Page 163 and 164:
Mask Testing Table 3- 5: Mask maker
Page 165 and 166:
Mask Testing Adding a Trace to a Ma
Page 167 and 168:
Mask Testing If you accidentally d
Page 169 and 170:
Mask Testing The YBA250 calculates
Page 171 and 172:
Saving and Recalling Results, Scree
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183:
Appendices
Page 186 and 187:
Appendix A: Specifications Table A-
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Appendix B: Accessories Optional Ac
Page 198 and 199:
Appendix C: Options C-2 YBA250 Ante
Page 200 and 201:
Appendix D: Upgrading/Reinstalling
Page 202 and 203:
Appendix E: Functional Verification
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Appendix F: Supported Signal Standa
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Appendix G: Customizing the Channel
Page 216 and 217:
Appendix G: Customizing the Channel
Page 219 and 220:
Glossary BMP - Graphics File Format
Page 221:
Index
Page 224 and 225:
Index D DC power adapter, 1-6 Defau
Page 226 and 227:
Index Tools, 2-16 View, 2 -14 Metho
Page 228:
Index T taskbar, desktop, 2-2 Techn
show all

YBA250 Antenna and Transmission Line Analyzer User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?