HERZ laying system

HERZ laying system
Plastic support bars
Self-adhesive, installation distance 500 to
1000 mm
Pipe diameter: 16 or 20 mm
Preset breaking point every 100 mm
Length 0.1 m Article No: 3 F110 01
Length 0.9 m Article No: 3 F110 02
Layout for wall heating
Plaster
Material requirement for 1 m² floor
heating with laying interval of 50 mm:
19 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
1 m² heat insulation 3 F070 xx
1 m² PE foil 3 F100 xx
0.2 litres of screed additive 3 F090 01
1 run metre adhesive tape 3 F090 02
0.7 running metres Edge
insulation strips 3 F080 02
Material requirement for 1 m² floor
heating with laying interval of 100 mm:
10 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
1 m² heat insulation 3 F070 xx
1m² PE foil 3 F100 xx
0.2 litres of screed additive 3 F090 01
1 run metres adhesive tape 3 F090 02
1 run metres adhesive tape 3 F080 02
Material requirement for 1 m² floor
heating with laying interval of 150 mm:
6.5 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
1 m² heat insulation 3 F070 xx
1 m² PE foil 3 F100 xx
0.2 litres of screed additive 3 F090 01
1 run metre adhesive tape 3 F090 02
0.7 running metres Edge
insulation strips 3 F080 02
Material requirement for 1 m² floor
heating with laying interval of 200 mm:
5 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
1 m² heat insulation 3 F070 xx
1 m² PE foil 3 F100 xx
0.2 litres of screed additive 3 F090 01
1 run metre adhesive tape 3 F090 02
0.7 running metres Edge
insulation strips 3 F080 02
Wall layout system with Clip rails
(to interior):
• Concrete or brick wall
• Clip rails with fixed dowels
• Heating pipes fixed with clip rails
• Rough plaster
• Refined plaster with plaster mesh
• Painting or wallpaper
HERZ system components for
clip rails variants
The clip rails are installed on the wall at
intervals of 50-100 cm. The heating pipes
are installed on these clip rails at the
appropriate interval.
Material requirement for 1 m² wall heating
with laying interval of 50 mm:
19 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres clip rails 3 F110 0x
4 units Screws and dowels on-site
1 m² plaster mesh on-site
Material requirement for 1 m² wall heating
with laying interval of 100 mm:
10 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
4 units Screws and dowels on-site
1 m² plaster mesh on-site
Materialbedarf für 1 m² Wandheizung mit
VA 150 mm:
6.5 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
4 units Screws and dowels on-site
1 m² plaster mesh on-site
Material requirement for 1 m² wall heating
with laying interval of 200 mm:
5 running metres HERZ floor
heating pipe, 16 x 2 3 D160 20
2 running metres Clip rails 3 F110 0x
4 units Screws and dowels on-site
1 m² plaster mesh on-site
Plaster mesh
HERZ pipe
Notched rails, F110
Wall
For additional fixing of the pipes or fixing of
the holding rails, the holding needles used
may be red or green.
Fixing-pins, red
For direct installation onto the insulation
layer with a thickness of over 30 mm. Due
to the special material used, these fixingpins
have outstanding fixing strength, which
can be increased by inserting the pin at an
oblique angle.
HERZ Article No: 3 F110 03
Fixing-pins, green
For direct installation onto the insulation
layer with a thickness of over 40mm. Due to
the special material used, these fixing-pins
have outstanding fixing strength, which
can be increased by inserting the pin at an
oblique angle.
HERZ Article No: 3 F110 04
16
Room heating and cooling for floors, walls and ceilings