Basic Information Selection Guide M451-110, August 2002 - Rexnord

More documents

Recommendations

Info

F A L K Type GV82 Standard Flanged Sleeve Rigid Thrust/Dimensions — Millimeters Type GV82 couplings are used as rigid connections for the low speed shaft of a gear drive and a mixer shaft or suspended load. The coupling carries the torque load, weight of the shaft and impeller, thrust forces and resulting bending moments. When a rigid coupling is required, the following additional information is necessary. 1. Required thrust capacity and direction of thrust. 2. Radial force at impeller. 3. Distance from the center of coupling fastener flange to the center of the impeller. 4. Weight of shaft and impeller. U F A KEYWAY DOWEL PINS RIGID COUPLING MIXER SHAFT U L E L GAP X-DIAMETER PILOT HOLE THRU ONE WALL IN EACH HUB AT 90 TO KEYWAY FOR W-DOWEL. AFTER MOUNTING HUBS, DRILL AND REAM THRU FOR .0010"T TO .0005"L DOWEL FIT. STAKE DOWELS IN PLACE. H H Q Q B SIZE Torque Rating (Nm) † Hub Bore Range (mm) Cplg Wt With No Bore-kg DIMENSIONS — Millimeters A B E F H L Q U Dowel Dia x Length W Dowel Hole-Dia +.0,0127 – .0,0000 1010GV 1 139 34,9 – 57,2 4,5 115,9 84,3 2,5 83,8 14,0 39,6 42,2 9,7 9,5 x 81,8 9,5 8,7 5 1010GV 1015GV 2 350 41,3 – 69,8 9,1 152,4 97,5 2,5 105,2 19,0 46,2 48,8 12,7 12,7 x 103,1 12,7 11,9 5 1015GV 1020GV 4 270 63,5 – 82,6 15,9 177,8 121,9 2,5 126,5 19,0 58,4 61,0 19,1 19,1 x 124,0 19,0 18,3 5 1020GV 1025GV 7 470 82,6 – 101,6 27,2 212,9 152,4 2,5 154,9 21,8 73,7 76,2 25,4 25,4 x 151,9 25,4 23,8 5 1025GV 1030GV 12 100 88,9 – 114,3 43,1 239,8 180,8 2,5 180,3 21,8 87,9 90,4 28,4 28,6 x 176,8 28,5 27,0 5 1030GV 1035GV 18 500 101,6 – 133,4 70,3 279,4 209,3 2,5 211,3 28,4 102,1 104,6 31,8 31,8 x 208,3 31,7 30,2 5 1035GV 1040GV 30 600 114.3 – 158,8 102 317,5 238,8 4,1 245,4 28,4 115,3 119,4 35,1 34,9 x 241,8 34,9 33,4 8 1040GV 1045GV 42 000 127,0 – 177,8 141 346,0 269,2 4,1 274,1 28,4 130,6 134,6 38,1 38,1 x 270,0 38,1 36,5 8 1045GV 1050GV 56 600 146,0 – 196,8 204 388,9 304,8 5,1 305,8 38,1 147,3 152,4 44,5 44,4 x 301,2 44,4 42,9 10 1050GV 1055GV 74 000 146,0 – 215,9 281 425,4 355,6 5,1 334,3 38,1 172,7 177,8 44,5 44,4 x 330,2 44,4 42,9 10 1055GV 1060GV 90 400 171,4 – 235,0 336 457,2 386,1 6,6 366,0 25,4 186,4 193,0 50,8 50,8 x 361,2 50,8 49,2 13 1060GV 1070GV 135 000 171,4 – 273,1 535 527,0 457,2 8,4 424,9 28,4 220,2 228,6 50,8 50,8 x 420,6 50,8 49,2 17 1070GV Refer to Page 13 for General Information and other Reference Notes. Dowels: diameters, +.000”,-.001” material, AISI 4140 hardness, 310-350HB; furnished by Falk. Customer is responsible for checking and furnishing driven shaft with satisfactory capacity. X Gap SIZE OTHER AXIAL RETENTION OPTIONS — AVAILABLE ON TYPE GXVF (Refer to Falk) KEEPER PLATE REGISTERED KEEPER PLATE WELDED 32 (M451-110) The Falk Corporation, 1998, 2002.
Type GR20 Standard Flanged Sleeve Shear Pin/Double Engagement Dimensions — Millimeters MINIMUM CLEARANCE REQUIRED FOR ALIGNING M M SHEAR PLATES HARDENED BUSHING AA C GAP C D F A SHEAR PIN X SHEAR NOTCH DIAMETER H B LUBRICATE THRU SLEEVE - BOTH SIDES SIZE Torque Rating (Nm) † Shear Torque (Nm ) Min Max Allow Speed rpm ‡ Cplg Wt With No Bore-kg Lube Wt (kg) DIMENSIONS — Millimeters A B C D F H M X AA Gap 1010GR 1 139 124 1 073 5000 8,62 0,0408 115,9 121,7 42,9 68,6 83,8 9,1 50,8 147,6 173,0 36 1010GR 1015GR 2 350 282 2 407 4000 15,0 0,0726 152,4 138,2 49,3 86,4 105,2 9,1 61,0 184,2 209,6 40 1015GR 1020GR 4 270 599 4 452 3600 28,1 0,1134 177,8 170,2 62,0 105,2 126,5 12,2 76,2 209,6 235,0 46 1020GR 1025GR 7 470 1 062 8 011 2700 49,0 0,2268 212,9 201,7 77,0 130,6 154,9 12,2 91,4 266,7 317,5 48 1025GR 1030GR 12 100 1 774 13 344 2400 66,2 0,3629 239,8 234,2 91,2 152,4 180,3 12,2 106,7 293,7 338,1 52 1030GR 1035GR 18 500 2 542 20 462 2100 102 0,5443 279,4 273,3 106,4 177,8 211,3 12,2 129,5 333,4 377,8 60 1035GR 1040GR 30 600 3 141 31 139 1900 138 0,9072 317,5 301,8 120,6 209,6 245,4 12,2 144,8 371,5 415,9 60 1040GR 1045GR 42 000 5 435 42 708 1800 185 1,0433 346,0 330,2 134,9 235,0 274,1 12,2 165,1 400,0 450,8 60 1045GR 1050GR 56 600 6 982 57 837 1750 279 1,7690 388,9 394,5 153,2 254,0 305,8 24,9 182,9 438,2 482,6 88 1050GR 1055GR 74 000 8 926 75 632 1500 362 2,2226 425,4 424,4 168,1 279,4 334,3 24,9 203,2 482,6 533,4 88 1055GR 1060GR 90 400 12 575 100 139 1400 441 3,1751 457,2 464,6 188,2 304,8 366,0 24,9 228,6 520,7 590,8 88 1060GR 1070GR 135 000 18 044 142 429 1250 670 4,3545 527,0 529,6 220,7 355,6 424,9 24,9 266,7 590,6 660,4 88 1070GR Refer to Page 13 for General Information and other Reference Notes. Minimum and maximum bores are the same as those for G20, Page 17. SIZE The Falk Corporation, 1998, 2002. (M451-110) 33
Page 1 and 2: Selection Guide M451-110, August 20
Page 3 and 4: Lifelign Gear Coupling Types With t
Page 5 and 6: Type G70 Disconnect couplings are u
Page 7 and 8: How to Select Formula Selection Met
Page 9 and 10: SERVICE FACTORS: are a guide, based
Page 11 and 12: Type GC05 Continuous Sleeve Single
Page 13 and 14: Type G20 Standard Flanged Sleeve Do
Page 15 and 16: Type G52 Standard Flanged Sleeve Si
Page 17 and 18: Type G52 Standard Flanged Sleeve Fl
Page 19 and 20: Type GV52 Standard Flanged Sleeve V
Page 21 and 22: Types G62/G66 Standard Flanged Slee
Page 23 and 24: Type GL52 Standard Flanged Sleeve S
Page 25 and 26: Type G72 Disconnect/Dimensions —
Page 27: Type G82 Standard Flanged Sleeve Ri
Page 31 and 32: Engineering Data — Standard Flang
Page 37 and 38: Type G52 Large Flanged Sleeve Singl
Page 39 and 40: Type GV20 Large Flanged Sleeve Vert
Page 41 and 42: Type GL20-4 Large Flanged Sleeve Sl
Page 43 and 44: Type G82 Large Flanged Sleeve Rigid
Page 45 and 46: Engineering Data — Large Flanged
Page 51 and 52: Engineering Data — All Gear Coupl
Page 53 and 54: Interchange Guide — Continuous Sl
Page 55 and 56: This Page Intentionally Left Blank

Basic Information Selection Guide M451-110, August 2002 - Rexnord

Create successful ePaper yourself

Delete template?

Save as template?