001 Stand Alone Low Voltage - Garney Construction

More documents

Recommendations

Info

Installation Instructions Wiring and Grounding Guidelines for Pulse Width Modulated (PWM) AC Drives
Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/ literature/) describes some important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. ! WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. Important: Identifies information that is critical for successful application and understanding of the product. ! ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequences. Shock Hazard labels may be located on or inside the equipment (e.g., drive or motor) to alert people that dangerous voltage may be present. Burn Hazard labels may be located on or inside the equipment (e.g., drive or motor) to alert people that surfaces may be at dangerous temperatures. Allen-Bradley, Rockwell Software, Rockwell Automation, PowerFlex, DriveExplorer, DriveExecutive, DPI, and SCANport are either trademarks or registered trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.
Page 1 and 2: Garney Construction 785 E Warren Ga
Page 3 and 4: PROJECT SUBMITTAL Project Owner: Wa
Page 5 and 6: Tab 3. Product References Circuit
Page 7 and 8: Practices that Guard against ESD Th
Page 9 and 10: Handling Sensitive Components Corre
Page 11 and 12: What Causes Electrostatic Damage? E
Page 13: If we pick up the chip, it becomes
Page 16 and 17: Safety Guidelines for the Applicati
Page 18 and 19: Section 1: Definitions 3 Section 1:
Page 20 and 21: Section 2: General Authorized Engin
Page 22 and 23: Section 2: General Authorized Engin
Page 24 and 25: Section 3: Application Guidelines 9
Page 34 and 35: Section 4: Installation Guidelines
Page 36 and 37: Section 4: Installation Guidelines
Page 38 and 39: Section 5 : Preventive Maintenance
Page 40 and 41: Section 5 : Preventive Maintenance
Page 43: Publication SGI - 1.1 — January 2
Page 47 and 48: soc-ii Summary of Changes Notes: Pu
Page 49 and 50: ii Table of Contents Chapter 6 Appe
Page 51 and 52: P-2 Overview Recommended Cable/Wire
Page 53 and 54: 1-2 Wire/Cable Types General Materi
Page 55 and 56: 1-4 Wire/Cable Types Figure 1.3 Cab
Page 57 and 58: 1-6 Wire/Cable Types Type 3 Install
Page 59 and 60: 1-8 Wire/Cable Types Type 3 Install
Page 61 and 62: 1-10 Wire/Cable Types Input Power C
Page 63 and 64: 1-12 Wire/Cable Types Analog Signal
Page 65 and 66: 1-14 Wire/Cable Types Remote I/O an
Page 67 and 68: 2-2 Power Distribution Delta/Delta
Page 69 and 70: 2-4 Power Distribution TN-S Five-Wi
Page 71 and 72: 2-6 Power Distribution Transformer
Page 73 and 74: 2-8 Power Distribution Table 2.C AC
Page 75 and 76: 2-10 Power Distribution Drive Catal
Page 77 and 78: 2-12 Power Distribution PowerFlex 7
Page 79 and 80: 2-14 Power Distribution 1336 Family
Page 81 and 82: 2-16 Power Distribution Example: Th
Page 83 and 84: 2-18 Power Distribution Using Power
Page 85 and 86: 2-20 Power Distribution Braking Cho
Page 87 and 88: 3-2 Grounding Grounding PE or Groun
Page 89 and 90: 3-4 Grounding The grounding scheme
Page 91 and 92: 3-6 Grounding Effective Grounding P
Page 93 and 94: 3-8 Grounding Notes: Publication DR
Page 95 and 96:
4-2 Practices Zinc-plated steel is
Page 97 and 98:
4-4 Practices Figure 4.3 Bolt Mount
Page 99 and 100:
4-6 Practices Figure 4.5 Terminatin
Page 101 and 102:
4-8 Practices Do not lay one ground
Page 103 and 104:
4-10 Practices Spacing Notes: 1. Bo
Page 105 and 106:
4-12 Practices Common Mode Current
Page 107 and 108:
4-14 Practices Cable Trays When lay
Page 109 and 110:
4-16 Practices Figure 4.14 Plain Co
Page 111 and 112:
4-18 Practices Conductor Terminatio
Page 113 and 114:
4-20 Practices Notes: Publication D
Page 115 and 116:
5-2 Reflected Wave (CIV) for the ai
Page 117 and 118:
6-2 Electromagnetic Interference Co
Page 119 and 120:
6-4 Electromagnetic Interference Pu
Page 121 and 122:
6-6 Electromagnetic Interference En
Page 123 and 124:
A-2 Motor Cable Length Restrictions
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
A-10 Motor Cable Length Restriction
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Glossary-2 Dry Dry locations per Pe
Page 157 and 158:
Glossary-4 Notes: Publication DRIVE
Page 159 and 160:
Index-2 Ungrounded Secondary, 2-3 D
Page 161:
Index-4 Surge Protection MOV, 2-17
Page 173 and 174:
Product Details and Certifications
Page 175 and 176:
http://raise.rockwellautomation.com
Page 177 and 178:
Page 179 and 180:
Yokogawa Corp. of America - Meter &
Page 183 and 184:
Career │ Site Map │ Contact Us
Page 185 and 186:
AMP-TRAP 2000 ® ATQR TIME DELAY/CL
Page 187 and 188:
AMP-TRAP 2000 ® TIME DELAY/CLASS C
Page 189 and 190:
Bussmann ® LOW-PEAK ® Time-Delay
Page 191 and 192:
Bussmann ® LOW-PEAK ® Time-Delay
Page 194 and 195:
Page 196 and 197:
Directory: Tools & Resources|Locati
Page 198 and 199:
Directory: Tools & Resources|Locati
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
9 KEY BENEFITS Unique protect
Page 210 and 211:
469 SR Motor Protection System 469
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Product Details Product Details Pro
Page 220 and 221:
POTENTIAL TRANSFORMERS THREE PHASE
Page 222 and 223:
PowerFlex 70/700 Production Test Pr
Page 224 and 225:
PowerFlex 70/700 Production Test Pr
Page 226 and 227:
TEST PROCEDURE Test No: TEST 5015-0
Page 228 and 229:
TEST PROCEDURE Test No: TEST 5015-0
Page 230 and 231:
Customer: The Reynolds Co. End User
Page 232 and 233:
Harmonic Estimator Report - Summary
Page 234 and 235:
Harmonic Estimator Report - Spectru
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
SMC-Flex Bulletin 150 SMC-Flex Appl
Page 282 and 283:
Bulletin 150 SMC-Flex Table of Cont
Page 284 and 285:
Bulletin 150 SMC-Flex Solid-State .
Page 286 and 287:
Bulletin 150 SMC-Flex Chapter 2 App
Page 288 and 289:
Bulletin 150 SMC Flex Chapter 1 Int
Page 290 and 291:
Bulletin 150 SMC Flex Standard Soft
Page 292 and 293:
Bulletin 150 SMC Flex Figure 1.4: S
Page 294 and 295:
Bulletin 150 SMC Flex Figure 1.6: C
Page 296 and 297:
Bulletin 150 SMC Flex Dual Ramp Sta
Page 298 and 299:
Bulletin 150 SMC Flex Figure 1.10:
Page 300 and 301:
Page 302 and 303:
Bulletin 150 SMC Flex Preset Slow S
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Bulletin 150 SMC Flex Soft Stop The
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Bulletin 150 SMC Flex Braking Contr
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Bulletin 150 SMC Flex Slow Speed wi
Page 322 and 323:
Page 324 and 325:
Bulletin 150 SMC Flex Electronic Ov
Page 326 and 327:
Bulletin 150 SMC Flex The SMC-Flex
Page 328 and 329:
Bulletin 150 SMC Flex The SMC-Flex
Page 330 and 331:
Bulletin 150 SMC Flex 2 Overview Ap
Page 332 and 333:
Bulletin 150 SMC Flex Figure 2.3: P
Page 334 and 335:
Bulletin 150 SMC Flex Figure 2.5: R
Page 336 and 337:
Bulletin 150 SMC Flex Figure 2.7: C
Page 338 and 339:
Bulletin 150 SMC Flex Figure 2.9: O
Page 340 and 341:
PROTECTIVE MODULE Bulletin 150 SMC
Page 342 and 343:
Bulletin 150 SMC Flex Built-in Comm
Page 344 and 345:
Bulletin 150 SMC Flex Multi-motor A
Page 346 and 347:
Bulletin 150 SMC Flex Part Winding
Page 348 and 349:
Bulletin 150 SMC Flex SMC-Flex Cont
Page 350 and 351:
Bulletin 150 SMC Flex SMC-Flex Cont
Page 352 and 353:
Bulletin 150 SMC Flex Motor Torque
Page 354 and 355:
Bulletin 150 SMC Flex Chapter 4 Des
Page 356 and 357:
Bulletin 150 SMC Flex Petrochemical
Page 358 and 359:
Bulletin 150 SMC Flex Chapter 5 Phi
Page 360 and 361:
Bulletin 150 SMC Flex Chapter 6 Int
Page 362 and 363:
Bulletin 150 SMC Flex There are two
Page 364 and 365:
Bulletin 150 SMC Flex Figure 6.8: S
Page 366 and 367:
Bulletin 150 SMC Flex Chapter 7 Sol
Page 368 and 369:
Bulletin 150 SMC Flex Chapter 8 Ref
Page 370 and 371:
Bulletin 150 SMC Flex Figure 8.2 il
Page 372 and 373:
Bulletin 150 SMC Flex For single ph
Page 374 and 375:
Bulletin 150 SMC Flex Motor Output
Page 376 and 377:
Bulletin 150 SMC Flex Calculating T
Page 378 and 379:
Bulletin 150 SMC Flex T (Accelerati
Page 380 and 381:
Bulletin 150 SMC Flex Application L
Page 382 and 383:
Bulletin 150 SMC Flex PF W = ------
Page 384 and 385:
Bulletin 150 SMC Flex Notes 8-17
Page 387 and 388:
Publication 150-AT002B-EN-P — Jun
Page 389 and 390:
Drives Support > Drive Maintenance
Page 391 and 392:
Drives Support > Drive Maintenance
Page 393 and 394:
SupportPlus For consultation on hig
Page 395 and 396:
SERVICE & SUPPORT Contract Callout
Page 398 and 399:
Table of Contents 1. Introduction 1
Page 400 and 401:
1.2.1 Feeder Input Data Sheet ALL P
Page 402 and 403:
2.1 Motor Starting Study Discussion
Page 404 and 405:
WPS RVSS Study1 - RVSS - MTRI-WPSSW
Page 406 and 407:
2.2.2 SKM TMS Solid State Voltage R
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
2500 1250 100 Percent Voltage Study
Page 414 and 415:
2.3.2 SKM TMS 100% Voltage Start Re
Page 416 and 417:
2.3.2 SKM TMS 100% Voltage Start Re
Page 418 and 419:
2.4 SKM TMS 80% Voltage Start This
Page 420 and 421:
2.4.2 SKM TMS 80% Voltage Start Rep
Page 422 and 423:
Page 424 and 425:
Page 426:
4. Information 30
show all

001 Stand Alone Low Voltage - Garney Construction

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?