Serial I/O - ICSDataCom

312 mm (without slot bracket/connector)
107 mm (without slot bracket)
202 mm 33 mm 77 mm
Specifications:
ME-3000
Analog inputs
Number 16 single-ended/8 differential channels; input resistance typ. 160
MΩ/input capacity: 3 pF
Ranges Programmable unipolar (single-ended) or bipolar (single-ended/differential):
x1: 0…10 V ±10 V x2: 0…5 V ±5 V
x4: 0…2,5 V ±2,5 V x8: 0…1,25 V ±1,25 V
Isolation Galvanic isolation of A/D the section from PC GND and from the rest
of the board up to 500 V. Inputs protected up to ±15 V
A/D converter 12 bit, sampling rate max. 500 kHz (depending on system)
Option SA 4 single-ended channels with simultaneous sampling and 12 “normal”
single-ended channels. Simultaneous sampling rates:
2 channels: ~150 kHz; 3 channels: ~115 kHz; 4 channels: ~93 kHz
Operating modes Single value, block of values, conversion with programmable channel
list (max. 1024 entries: Channel number, gain, uni-/bipolar, singleended/differential);
2 k FIFO for A/D data
Trigger
Internal (A/D timing counter), external TTL trigger
Analog outputs
Number 4 independent channels with 1 sense line per channel (automatic
stabilisation of the output voltage depending on the load)
Ranges 0…10 V, ±5 V, ±10 V programmable for each channel individually. Output
current max. 2 mA per channel
D/A converter Quad 12 bit D/A converter; sampling rate max. 100 kHz (at ±10 V;
actual rate depending on system).
Operating modes Single value (buffered/transparent) or simultaneous output (buffered);
VEC-2/3 additional Continuous or WrapAround mode, 4 k FIFO
for D/A output (VEC-2 and 3)
Digital I/O (TTL), PWM, counters
Number 32 I/O channels (2x 16 bit independent ports as inputs or outputs)
Level
Outputs: Low max. 0.5 V/24 mA; high min. 2 V/-15 mA;
inputs: Low max. 0.8 V; high min. 2 V
PWM
1 output for puls width modulation (pin 32) on the models VEC-2 and
3; duty cycle: 0…99% in steps of 1%. Frequency range up to 30 kHz;
can be divided down to 0.4 Hz using the 16 bit counter. Output
voltage at max. output current low: Max. 0.33 V ati 6 mA; high: Min.
3.84 V at -6 mA; input voltage low: Max. 0.8 V; high: Min. 2 V
Counter 2x 16 bit counters on the models VEC-1 and 3; functions: Load
start value/end value, interrupt on zero, latched reading of present
counter value. External clock max. 6 MHz (end value = 65535), max.
90 kHz (end value < 65535). Min. pulse width 60 ns (high level)
Serial interface (optional for ME-3000 PCI-Modelle)
Operating modes RS422, RS485 half duplex, RS485 full duplex; distance max.
1200 m; all lines opto-isolated; output current max. 100 mA. UART
16C550 with 16 Byte FIFO
Rates 1.200, 2.400, 4.800, 9.600, 19.200, 38.400, 57.600,
115.200 Baud
Transmission Parity: No/even/odd, data bits: 7/8, stop bits: 1/2
General
Bus interface 32 bit StandardPCI bus oder CompactPCI/PXI bus. PCI Local Bus 2.1
compatible
Size (mm) PCI: ~312 x 107 (without slot bracket/connector - for details see
picture/drawing); CompactPCI/PXI: 160 x 100 (3 U)
Connectors 78-pin D-sub female.
Option SIO/RS485: 10-pin connector with fl at ribbon cable and an
additional slot bracket with 9-pin D-sub female (see picture)
Meilhaus Electronic Data Acquisition Boards
42 mm 65 mm
Slot bracket + D-sub
female of option SIO
(RS422/485
Software:
Including: ME-Power-CD with…
Drivers for Windows 98/Me, NT, 2000, XP.
Supports Visual C++, Delphi, Visual Basic and
Borland C/C Builder.
Driver for Agilent VEE und LabVIEW.
Drivers for QNX (source code under QNX
Community License)
Drivers for VxWorks 5.4.2.
Utilities, examples, demos.
“Soft manuals” English and German, for Acrobat
Reader (printed manuals as an option/extra
charge)
Ordering Code:
ME-3000 PCI VEC-1 1450.00 $
PCI multi I/O board for data acquisition: Isolated
12 bit/500 kHz A/D, additional A/D features, 12 bit
D/A, digital I/O, 2x 16 bit counters
ME-3000 PCI VEC-2 1835.00 $
PCI multi I/O board for prozess control and signal
generation: Isolated 12 bit/500 kHz A/D, 12 bit
D/A, additional D/A-features, digital I/O, PWM
ME-3000 PCI VEC-3 2150.00 $
versions VEC-1 + 2 on one board
ME-3000 PCI VEC-1 SA 1765.00 $
ME-3000 PCI VEC-3 SA 2450.00 $
See PCI model VEC-1 or -3, but with 4 channels with
simultaneous sampling and 12 standard single-ended
channels
ME-3000 PCI VEC-1 SIO
ME-3000 PCI VEC-2 SIO
ME-3000 PCI VEC-3 SIO
Accessories:
Cable ME AK-D78/1 (1 m) 92.00 $
78-pin D-sub male and 78-pin D-sub female (1:1),
connects ME-3000 to terminal block, ME-MultiSig®
boards or user application
Terminal block ME AB-D78M 145.00 $
78-pin D-sub male and spring terminals
Terminal block ME AB-BNC16 185.00 $
78-pin D-sub male and16 BNC.
ME-MultiSig® series
Multiplexing, demultiplexing and signal-conditioning
system
Web: www.meilhaus.com/e_me
on request
on request
on request
See model VEC-1, -2 or -3, but with additional isolated,
RS485-interface, incl. ribbon cable + connector/slot
bracket
ME-3000 cPCI VEC-1 1595.00 $
ME-3000 cPCI VEC-2 2095.00 $
ME-3000 cPCI VEC-3 2395.00 $
ME-3000 cPCI VEC-1 SA 1925.00 $
ME-3000 cPCI VEC-3 SA 2695.00 $
See above, but for CompactPCI/PXI platform
Web: www.meilhaus.com/e_me
15