Installation and Operating Instructions GEN-AUTO Energy Division

More documents

Recommendations

Info

Section 3 Programming 3.1 Procedure Many of the unit functions can be set by programming. Programming can be carried out only while the unit is in Stop mode. Proceed as follows: 1. If the unit is off, press the button to turn it on. 2. Press the button. If the engine is running, it will stop. 3. Press the button and hold it, for approximately 10 seconds, until the PROG LED lights. 4. You may enter either an Operator password or a Technician password. The Operator password restricts access to the primary programming functions P00-08 and P38 only. The Technician password gives access to all programming functions. If you wish to enter the Operator password, press . To enter the Technician password, press for ten seconds and then . In both cases, the display shows 0000. 5. Use the and keys to increment and decrement the display until it shows the correct password. When the unit is initially supplied, the password for both Operator and Technician is 0000. To prevent unauthorised access, use parameter P37 to change the Operator password and parameter P38 to change the Technician password. The Technician password is only accessible if you have entered as a technician. 6. Press to confirm your password entry. If the password is incorrect, the unit will drop out of Program mode. If the password is correct, the display will show the first programmable parameter – P00. You are now in program mode. If no keys are pressed for a period of approximately 20 seconds, the unit will return to the normal operating mode. 7. To view or change a parameter, press the key repeatedly until the display shows the parameter number and then press value of the selected parameter. to select it. The display will show the current 8. Use the and keys to set the displays to the required value. 9. Press to accept the displayed value. The display will show the number of the next parameter in the sequence. 18
10. To exit the programming mode, press . Table 3 Programmable function definitions Prg Definition of parameter Unit Lower / Default No. Upper Limit P00 Alternator Voltage Lower Limit VAC 60-600 300 P01 Alternator Voltage Upper Limit VAC 60-600 440 P02 Speed Lower Limit Hz. 30.0-75.0 47.0 P03 Speed Upper Limit Hz. 30.0-75.0 53.0 P04 Battery Voltage Lower Limit VDC 7.2-24.0 8.0 P05 Reserved P06 Periodic Maintenance Hour Set Hour 0-9999 5000 P07 Periodic Maintenance Reset Press DECREMENT Button For Reset P08 Horn Duration Second 0 = Contin. 1-999 60 P09 Preheat time Second 0 – 99 10 P10 Single/Three Phase Selection 1/3 3 P11 Nominal Alternator Frequency Hz. 50 / 60 50 P12 Nominal Speed (RPM) Rpm 500-5000 3000 P13 Number of Flywheel Teeth Number 1-1000 100 P14 Reserved Speed Sensing Input Selection P15 0-Alternator Signal (Internal) Number 0 / 1 0 1-Magnetic Pickup P16 Stop/Fuel Solenoid Selection Stop / Fuel Stop / Fuel Fuel P17 Stop Magnet Energising Time Second 0-99 20 P18 Engine Started Signal 0: No, 1: Yes P18.0 Charge Generator 0/1 1 P18.1 Speed 0/1 0 P18.2 Alternator Voltage 0/1 1 P18.3 Oil Pressure 0/1 0 P19 Battery Voltage Weak Limit VDC 6.0-14.4 7.0 P20 Battery Voltage Weak Control Time Second 1-99 3 19
Page 1 and 2: Energy Division http://energy.tycoe
Page 3 and 4: Contents Page Section 4 Commissioni
Page 5 and 6: Section 1 Introduction These produc
Page 7 and 8: Figure 2.1 Unit fixing Figure 2.1 F
Page 9 and 10: Figure 2.5 GEN-AUTO single phase co
Page 11 and 12: Table 1 shows the connections and r
Page 13: 2.4.1 Charge Generator current The
Page 17 and 18: Prg Definition of parameter Unit Lo
Page 19 and 20: 3.2.8 Engine started signals (P18)
Page 21 and 22: 2 This is the same as 1 but, in add
Page 23 and 24: Section 5 Operation 5 6 7 5.1 Contr
Page 25 and 26: Control functions: 9. Green LED lig
Page 27 and 28: 6.2.5 Low/High Speed LED This LED f
Page 29 and 30: Section 7 Specification Inputs DC S
Page 31 and 32: Section 8 PC Interface 8.1 Introduc
Page 33 and 34: 8.3.1 Observation Window This windo
Page 35 and 36: 8.4 Main Menu 8.4.1 File This menu
Page 37 and 38: 8.5 Operation 8.5.1 Accessing Opera
Page 39 and 40: 8.5.4 Saving Parameters to a Config
Page 41 and 42: Programming Reference Sheet Prog No

Installation and Operating Instructions GEN-AUTO Energy Division

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?