Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...

More documents

Recommendations

Info

Maintenance Instructions Press the alternator to the direction of the thermostat housing. Now the v-belt can be changed (type: XPZ 850). Stretch the v-belt by pulling the alternator back. The v-belt should be able to be pressing approx. 1cm with the thumb. Tighten the fixing srews above and below the alternator. Page 24 Panda PMS 8 "mini" E-TEC s00585 - Chapter B: Maintenance Instructions
Maintenance Instructions B.6 The raw water circuit B.6.1 Clean raw water filter The raw water filter should be released regularly from arrears. In each case the water cock must be closed before. It is mostly sufficient to beat the filter punnet. If water should seep through the cover of the raw water filter, this may be sealed in no case with adhesive or sealant. Rather must be searched for the cause for the leakage. In the simplest case the sealing ring between caps and filter holders must be exchanged. B.7 Causes with frequent impeller waste The impeller of the cooling water pump must be regarded as wearing part. The life span of the impeller can be extremely different and exclusively depends on the operating conditions. The cooling water pumps of the PANDA generators are laid out in such a way that the number of revolutions of the pump lies low compared with other gensets. This is for the life span of the pump a positive effect. Unfavorably affects the life span of the impeller, if the cooling water sucking in way is relatively long or the supply is handicapped, so that the cooling water sucking in range develops a negative pressure. This can reduce first of all the power of the cooling water pump extremely that the wings of the impeller are exposed to very strong loads. This can shorten the life span extremely. Further the operation of the impeller pump loaded in waters with a high portion of suspended matters. The use of the impeller pump is particularly critical in coral waterbodies. Cases are well-known, which a impeller pump had so strongly run after 100 hours already that the lip seal on the wave was ground in. In these cases sharp crystal parts of the coral sand assess in the rubber seal and affect like an abrasive the high-grade steel shank of the impeller pump. If the generator were mounted over the water level it is particularly unfavorable for the impeller pump. After the first start some seconds will pass by, until the impeller can suck in cooling water. This short unlubricated operation time damages the impeller. The increased wear can lead after short time to the loss. (see special notes: "Effects on the impeller pump, if the generator is mounted over the waterline") Panda PMS 8 "mini" E-TEC s00585 - Chapter B: Maintenance Instructions Page 25
Page 1 and 2: Installation Manual Installation, M
Page 3 and 4: CALIFORNIA Proposition 65 Warning D
Page 5 and 6: Table of Contents A Mode of Operati
Page 7 and 8: D.7.2 Installation of the remote co
Page 9 and 10: Mode of Operation of the Generator
Page 19 and 20: Maintenance Instructions B. Mainten
Page 21 and 22: Maintenance Instructions Oil filter
Page 23 and 24: Maintenance Instructions 2. Push
Page 25 and 26: Maintenance Instructions B.5 De-aer
Page 27: Maintenance Instructions B.5.1 Drai
Page 31 and 32: Maintenance Instructions Pull to th
Page 33 and 34: Maintenance Instructions B.9 Conser
Page 35 and 36: Generator Failure C. Generator Fail
Page 37 and 38: Generator Failure C.3 Adjusting Ins
Page 39 and 40: Generator Failure If the adjustment
Page 41 and 42: Generator Failure The mechanical vo
Page 43 and 44: Generator Failure C.4.3 Checking th
Page 45 and 46: Generator Failure C.5 Generator pro
Page 47 and 48: Generator Failure Damage to starter
Page 49 and 50: Installation Instruction D. Install
Page 51 and 52: Installation Instruction D.3 Coolin
Page 53 and 54: Installation Instruction ...and ben
Page 55 and 56: Installation Instruction D.4 The Fr
Page 57 and 58: Installation Instruction Anti-freez
Page 59 and 60: Installation Instruction D.4.5 Sche
Page 61 and 62: Installation Instruction D.5.2 Exha
Page 63 and 64: Installation Instruction Example of
Page 65 and 66: Installation Instruction D.6.3 Conn
Page 67 and 68: Installation Instruction D.7.1 Conn
Page 69 and 70: Installation Instruction 1. Speed s
Page 71 and 72: Installation Instruction The cam-ty
Page 73 and 74: Installation Instruction D.8.3 VCS-
Page 75 and 76: Installation Instruction In additio
Page 77 and 78: Installation Instruction D.11 Instr
Page 79 and 80:
Tables E. Tables E.1 Troubleshootin
Page 81 and 82:
Tables Damaged bearing(s) piston (s
Page 83 and 84:
Tables Table 1: Voltage values stat
Page 85 and 86:
Tables E.2 Technical data Panda PMS
Page 87 and 88:
Tables E.4 Inspection checklist for
Page 89 and 90:
Tables E.6 Coolant specifications U
Page 91 and 92:
Tables J4, External potentiometer c
Page 93 and 94:
Tables E.8 Scheme measuring board E
Page 95 and 96:
Tables E.9.1 Legend relay board Par
Page 97 and 98:
5 Safety steps to follow if someone
show all

Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...