Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...

More documents

Recommendations

Info

Generator Failure Page 44 Panda PMS 8 "mini" E-TEC s00585 - Chapter C: Generator Failure
Installation Instruction D. Installation Instruction D.1 Placement D.1.1 Placement and Basemount Since Panda generators have extremely compact dimensions they can be installed in tight locations, attempts are sometimes made to install them in almost inaccessible places. Please consider that even almost maintenance-free machinery must still remain accessible at least at the front (drive belt, water pump) and the service-side (actuator, dipstick). Please also note that in spite of the automatic oil-pressure sensor it is still essential that the oil level has to be checked regularly. The generator should not be installed in the proximity of light walls, which can get into resonant vibrations by airborne sound. If this is not possible, these surfaces should line with 1mm lead foil, so the mass and the swinging behavior are changed. Avoid to install the generator on a smooth surface with small mass (e.g. plywood plate). This affects in the unfavorable case like an amplifier the airborne sound waves. An improvement obtains by compound these surfaces by ribs. Also break-throughs should be sawed, which interrupt the surface. Disguising the surrounding walls with a heavy layer (e.g. lead) plus foam material improves the conditions additionally. The engine draws its inlet combustion air through several holes in the capsule base. Therefore the capsule must be fitted with sufficient clearance between the capsule underside and the base plate (min. 12mm (½")). The generator sucks its air from the surrounding engine room. Therefore it must be ensured that sufficient ventilation openings are present, so that the genset cannot overheat. High temperature of the intake air decline the power of the genset and increases the coolant temperature. Air temperatures of more than 40°C reduce the power by 2% per temperature rise of 5°C. In order to keep these effects as small as possible, the temperature in the engine room should not be higher than 15°C in relation to the outside temperature. D.1.2 Notice for optimal sound insulation The convenient base consists of a stable framework, on which the generator is fastened by means of shock-mounts. Since the genset is "free" downward, the combustion air can be sucked in unhindered. In addition are void the vibrations, which would arise with a closed soil. Panda PMS 8 "mini" E-TEC s00585 - Chapter D: Installation Instruction Page 45
Page 1 and 2: Installation Manual Installation, M
Page 3 and 4: CALIFORNIA Proposition 65 Warning D
Page 5 and 6: Table of Contents A Mode of Operati
Page 7 and 8: D.7.2 Installation of the remote co
Page 9 and 10: Mode of Operation of the Generator
Page 19 and 20: Maintenance Instructions B. Mainten
Page 21 and 22: Maintenance Instructions Oil filter
Page 23 and 24: Maintenance Instructions 2. Push
Page 25 and 26: Maintenance Instructions B.5 De-aer
Page 27 and 28: Maintenance Instructions B.5.1 Drai
Page 29 and 30: Maintenance Instructions B.6 The ra
Page 31 and 32: Maintenance Instructions Pull to th
Page 33 and 34: Maintenance Instructions B.9 Conser
Page 35 and 36: Generator Failure C. Generator Fail
Page 37 and 38: Generator Failure C.3 Adjusting Ins
Page 39 and 40: Generator Failure If the adjustment
Page 41 and 42: Generator Failure The mechanical vo
Page 43 and 44: Generator Failure C.4.3 Checking th
Page 45 and 46: Generator Failure C.5 Generator pro
Page 47: Generator Failure Damage to starter
Page 51 and 52: Installation Instruction D.3 Coolin
Page 53 and 54: Installation Instruction ...and ben
Page 55 and 56: Installation Instruction D.4 The Fr
Page 57 and 58: Installation Instruction Anti-freez
Page 59 and 60: Installation Instruction D.4.5 Sche
Page 61 and 62: Installation Instruction D.5.2 Exha
Page 63 and 64: Installation Instruction Example of
Page 65 and 66: Installation Instruction D.6.3 Conn
Page 67 and 68: Installation Instruction D.7.1 Conn
Page 69 and 70: Installation Instruction 1. Speed s
Page 71 and 72: Installation Instruction The cam-ty
Page 73 and 74: Installation Instruction D.8.3 VCS-
Page 75 and 76: Installation Instruction In additio
Page 77 and 78: Installation Instruction D.11 Instr
Page 79 and 80: Tables E. Tables E.1 Troubleshootin
Page 81 and 82: Tables Damaged bearing(s) piston (s
Page 83 and 84: Tables Table 1: Voltage values stat
Page 85 and 86: Tables E.2 Technical data Panda PMS
Page 87 and 88: Tables E.4 Inspection checklist for
Page 89 and 90: Tables E.6 Coolant specifications U
Page 91 and 92: Tables J4, External potentiometer c
Page 93 and 94: Tables E.8 Scheme measuring board E
Page 95 and 96: Tables E.9.1 Legend relay board Par
Page 97 and 98: 5 Safety steps to follow if someone

Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Marine Generator Panda PMS 8 âminiâ E-TEC Icemaster Fischer ...