KM-650MAH-E Service manual - Hoshizaki

More documents

Recommendations

Info

C. Preparing the Icemaker for Periods of Non-Use NOTICE • When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. • To prevent damage to the water pump seal, do not operate the icemaker with the control switch in the "WASH" position when the water tank is empty. When the icemaker is not used for two or three days under normal conditions, it is sufficient to move the control switch to the "OFF" position, When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below. 1. Remove the water from the icemaker water supply line: 1) Remove the front panel. Move the control switch to the "OFF" position, then unplug the icemaker from the mains socket. 2) Close the icemaker water supply line shut-off valve and open the icemaker water supply line drain valve. 3) Allow the line to drain by gravity. 4) Attach a compressed air or carbon dioxide supply to the icemaker water supply line drain valve. 5) Make sure at least 3 minutes have elapsed since you unplugged the icemaker. Plug the icemaker back into the mains socket, then move the control switch to the "ICE" position. Replace the front panel in its correct position. 6) Blow the icemaker water supply line out using the compressed air or carbon dioxide supply. 7) Close the icemaker water supply line drain valve. 2. Drain the water tank: 1) Remove the front panel. Move the control switch to the "OFF" position, then unplug the icemaker from the mains socket. 2) Remove the base cover. 3) Disconnect one end of the pump tubing to drain the water tank. After the water tank has drained, reconnect the pump tubing. See Fig. 6. 4) Remove all ice from the storage bin. Clean the storage bin using a neutral cleaner. Rinse thoroughly after cleaning. 5) Replace the front panel in its correct position. Disconnect This End of Pump Tubing to Drain Water Tank Base Cover Fig. 6 58
VII. Disposal This icemaker contains refrigerant and must be disposed of in accordance with applicable national, state, and local codes and regulations. Refrigerant must be recovered by properly certified service personnel. 59
Page 1 and 2:
Hoshizaki America, Inc. Modular Cre
Page 3 and 4:
IMPORTANT This manual should be rea
Page 5 and 6:
Important Safety Information Throug
Page 7 and 8: I. Specifications A. KM-320MAH-E AC
Page 9 and 10: C. KM-650MAH-E AC SUPPLY VOLTAGE 22
Page 11 and 12: 2. KM-515MAH-E Main Transformer (23
Page 13 and 14: B. Sequence of Operation 1. Sequenc
Page 15 and 16: ) "G" Control Board KM-320MAH-E and
Page 17 and 18: 2. Sequence Flow Chart a) "E" Contr
Page 19 and 20: C. Control Board • A Hoshizaki ex
Page 25 and 26: ) Harvest Timer (S4 dip switch 1 &
Page 27 and 28: (2) Harvest Pump Timer, "G" Control
Page 29 and 30: III. Technical Information A. Water
Page 31 and 32: 2. Mechanical Bin Control KM-320MAH
Page 33 and 34: 2. KM-515MAH-E APPROXIMATE ICE AMBI
Page 35 and 36: IV. Service Diagnosis WARNING • T
Page 37 and 38: 5) Freeze Cycle - LED 1 is on. Comp
Page 39 and 40: B. Control Board Check Before repla
Page 41 and 42: 2. Mechanical Bin Control Check and
Page 43 and 44: D. Float Switch Check and Cleaning
Page 45 and 46: E. Thermistor Check To check thermi
Page 47 and 48: No Ice Production - Possible Cause
Page 49 and 50: 3. Low Ice Production Low Ice Produ
Page 51 and 52: 2. Brazing WARNING • R-404A itsel
Page 53 and 54: B. Important Notes for Component Re
Page 55 and 56: 1. Cleaning Procedure 1) Dilute 16
Page 57: B. Maintenance This icemaker must b
show all

KM-650MAH-E Service manual - Hoshizaki

Create successful ePaper yourself

Delete template?

Save as template?