Model 24927 - Ready Remote

More documents

Recommendations

Info

➜ System Maintenance The system requires no specific maintenance. Your transmitter is powered by a miniature 12-volt battery (type 23A) that will last approximately one year under normal use. When the battery begins to weaken, the operating range will be reduced. ➜ FCC/Id Notice This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Warning! Safety First The following safety warnings must be observed at all times: When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, the following recommendations should be made to all users of this system: 1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). © 2007 Directed Electronics 9
2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled by placing the system into Valet Mode. 3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control units to assure that the system does not unintentionally remote start the vehicle. 4. The user must install a carbon monoxide detector in or about the living area adjacent to the vehicle. All doors leading from adjacent living areas to the enclosed or partially enclosed vehicle storage area must remain closed at all time. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this user’s guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. After the remote start module has been installed, test the remote start module in accordance with the Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDI- ATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. 10 © 2007 Directed Electronics
Page 1 and 2: Model 24927 ➤Owner’s/Installati
Page 3 and 4: Consumer's remedy is limited to rep
Page 5 and 6: 6 © 2007 Directed Electronics
Page 7: Important Information Congratulatio
Page 11 and 12: H1 Harness - 6 pin connector H1/1 H
Page 13 and 14: H3 harness - 3 pin connector H3/1 H
Page 15 and 16: Step 1, Heavy Gauge Wire Connection
Page 17 and 18: With the key in the off position, t
Page 19 and 20: Accessory and Starter Wires The sta
Page 21 and 22: Many Nissan and Toyota vehicles hav
Page 23 and 24: Parking Light Flash There are sever
Page 25 and 26: Crimp your spade connector to the h
Page 27 and 28: All other door lock systems will re
Page 29 and 30: Important: Remember that these wire
Page 31 and 32: Type C: Direct-wired reversing pola
Page 33 and 34: Type D: Adding one or more aftermar
Page 35 and 36: Type F: One-wire system - cut to lo
Page 37 and 38: Determining the Proper Resistor Val
Page 39 and 40: Determining the Proper Resistor Val
Page 41 and 42: Tachometer Wire WARNING! In the fol
Page 43 and 44: Following is a brief description of
Page 45 and 46: Headlight Control wire The Yellow/B
Page 47 and 48: 48 © 2007 Directed Electronics
Page 49 and 50: Step 7, Programming Programming tra
Page 51 and 52: Transmitter Button Programming Char
Page 53 and 54: 3. Press a button on the transmitte
Page 55 and 56: Feature Menu 1 Descriptions 1. Engi
Page 57 and 58: 2. Siren: The output will be consta
Page 59 and 60:
2. Locking Type: Selects the type o
Page 61 and 62:
10. Alarm Chirps: Selects if the "B
Page 63 and 64:
Alarm Input Chart LED Flashes Input
Page 65 and 66:
Last Start Diagnostics: The system
Page 67 and 68:
Testing the System Once steps 1-7 h
Page 69 and 70:
2. Make sure the hood is closed and
Page 71 and 72:
➜ The remote start will not activ
Page 73 and 74:
74 © 2007 Directed Electronics
Page 75 and 76:
➤ ➤ ➤ ➤ ➤ Trunk release o
Page 77 and 78:
Note! If the lights flash more than
Page 79 and 80:
flashing to indicate Quick Stop Mod
Page 81 and 82:
Note! The alarm functions will be f
Page 83 and 84:
Auto-rearming feature Auto-rearming
Page 85 and 86:
To activate Panic Mode: ➤ Press a
Page 87 and 88:
Convenience Features Carfinder Feat
Page 89 and 90:
Glossary of Terms Control Module: T
Page 91 and 92:
Page 93 and 94:
Page 95:
The company behind this system is D
show all

Model 24927 - Ready Remote

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?