Model 24927 - Ready Remote

More documents

Recommendations

Info

Alarm and Security Features Transmitter Arming of the Alarm You can arm the system by pressing the button of your transmitter for one second. When the system arms, the Horn/Siren output will chirp once and the parking lights will flash once. If the power door locks are controlled by the system, the doors will also lock. While the system is armed, the status LED will flash once per second, indicating that the system is actively protecting your vehicle. If the Horn/Siren pulses and the lights flash 3 times, refer to the Diagnostics Section. This indicates an alarm input is active at the time of arming and should be checked. The LED will flash in groups to indicate the active input. Passive Arming of the Alarm This system can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door. Whenever the system is in its 30-second passive arming countdown, the status LED will flash rapidly. At the 30-second point, the Horn/Siren will chirp and the parking lights will flash to indicate that the system is armed. Note! If the door, brake or hood inputs are activated during the 30 second countdown the timer will stop and reset, it will re-start once the input becomes inactive. Active sensor inputs will not stop the countdown. © 2007 Directed Electronics 83
Auto-rearming feature Auto-rearming is designed to protect the vehicle in case of unintended disarming of the alarm. It will automatically re-arm the alarm and lock the doors 120 seconds after any transmitter disarm occurs. To stop Auto-rearm, open a door or turn the ignition on before the 120 seconds expires. Alarm Input Operations When armed, the alarm has 6 inputs which can cause a full alarm trigger output. Refer to the Alarm Diagnostic section for additional detail. ➤ ➤ The Door, Hood, Ignition and Brake inputs will cause an immediate full trigger output when activated. The Sensor inputs can cause two types of outputs; Warn-away and Full Trigger. Alarm Trigger Outputs ➤ ➤ Note! An optional two-stage sensor (p/n 504d) is required for the Sensor outputs to activate. Call Technical Support for more information on compatible sensors. Warn-away output: this output consists of 5 chirps of the Horn/Siren output and 3 flashes of the parking lights. Full Trigger output: this output consists of flashing the Parking lights and the Horn/Siren output for 30 seconds followed by a 5 second pause to monitor the alarm inputs. If an alarm input is still active the output will repeat. 84 © 2007 Directed Electronics
Page 1 and 2:
Model 24927 ➤Owner’s/Installati
Page 3 and 4:
Consumer's remedy is limited to rep
Page 5 and 6:
6 © 2007 Directed Electronics
Page 7 and 8:
Important Information Congratulatio
Page 9 and 10:
2. When parking in an enclosed or p
Page 11 and 12:
H1 Harness - 6 pin connector H1/1 H
Page 13 and 14:
H3 harness - 3 pin connector H3/1 H
Page 15 and 16:
Step 1, Heavy Gauge Wire Connection
Page 17 and 18:
With the key in the off position, t
Page 19 and 20:
Accessory and Starter Wires The sta
Page 21 and 22:
Many Nissan and Toyota vehicles hav
Page 23 and 24:
Parking Light Flash There are sever
Page 25 and 26:
Crimp your spade connector to the h
Page 27 and 28:
All other door lock systems will re
Page 29 and 30:
Important: Remember that these wire
Page 31 and 32: Type C: Direct-wired reversing pola
Page 33 and 34: Type D: Adding one or more aftermar
Page 35 and 36: Type F: One-wire system - cut to lo
Page 37 and 38: Determining the Proper Resistor Val
Page 39 and 40: Determining the Proper Resistor Val
Page 41 and 42: Tachometer Wire WARNING! In the fol
Page 43 and 44: Following is a brief description of
Page 45 and 46: Headlight Control wire The Yellow/B
Page 47 and 48: 48 © 2007 Directed Electronics
Page 49 and 50: Step 7, Programming Programming tra
Page 51 and 52: Transmitter Button Programming Char
Page 53 and 54: 3. Press a button on the transmitte
Page 55 and 56: Feature Menu 1 Descriptions 1. Engi
Page 57 and 58: 2. Siren: The output will be consta
Page 59 and 60: 2. Locking Type: Selects the type o
Page 61 and 62: 10. Alarm Chirps: Selects if the "B
Page 63 and 64: Alarm Input Chart LED Flashes Input
Page 65 and 66: Last Start Diagnostics: The system
Page 67 and 68: Testing the System Once steps 1-7 h
Page 69 and 70: 2. Make sure the hood is closed and
Page 71 and 72: ➜ The remote start will not activ
Page 75 and 76: ➤ ➤ ➤ ➤ ➤ Trunk release o
Page 77 and 78: Note! If the lights flash more than
Page 79 and 80: flashing to indicate Quick Stop Mod
Page 81: Note! The alarm functions will be f
Page 85 and 86: To activate Panic Mode: ➤ Press a
Page 87 and 88: Convenience Features Carfinder Feat
Page 89 and 90: Glossary of Terms Control Module: T
Page 95: The company behind this system is D
show all

Model 24927 - Ready Remote

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?