Technical Specification for - Gujarat Electricity Board

More documents

Recommendations

Info

TECHNICAL SPECIFICATION FOR SDH/PDH Equipment with integrated Access Multiplexer j) Bidder should confirm remote support to be provided through internet (secure connection) for quick trouble shooting. k) The offered FOTE shall provide one single platform for whole range of application from 64kbits/sec to STM-4. It also supports Expansion / Up gradation in future possible up to STM-16 or STM-64 depending on the needs of time. 2.0 1) In case the bidder dose not meet technical experience specified at 1.0 above at its own, the bidder should associate with firm(s) to form a JV/Consortium and the JV/Consortium shall collectively meet the requirement as per 1.0 above. 3.0 However, in respect of supply qualifications for supply requirement as per 1(b) & 1(d) , the Licensee / Licensor arrangement is permitted provided Licensor meeting the requirement of 1(b) to 1(k) stated herein above and shall also meet the following conditions; I Manufacture / Licensee shall have adequate design infrastructure and manufacturing facility and capacity and procedures including quality control for offered FOTE which should have to meet all the stipulated requirement of TS. II A qualified Licensee of a qualified manufacturer shall comply with all the following requirements and furnish a joint under taking by the Licensor along with the bidder in its bid as per the Annexure-I enclosed. a. Any design undertaken by the Licensee shall be approved by the Licenser. b. Manufacturing by the Licensee having manufacturing based in India shall be done with the approval of the Licenser and Employer under a quality assurance programme approved and monitored by the Licenser. c. Licensee must furnish back-up guarantee from the Licenser for individual and overall performance of all materials supplied under the contract. d. Licenser must guarantee sequential and timely supply of materials and submission of technical information and data as desired by the Employer so as to meet the overall project schedule and e. The agreement between Licensee and Licenser (copy to be submitted along with the bid) shall be valid for a period of at least five(5) years after the guarantee period of equipment ( Minimum period up to Dec- 2021) [B] Financial Requirement 1. Minimum Annual Turnover (MAT) for best three individual years out of last five financial years shall not be less than the estimated cost. (For Individual Bidders) 2. Minimum Annual Turnover (MAT) of the consortium / Joint Venture (JV) Company added together for best three individual years out of last five financial years shall not be less than the estimated cost. However Minimum Annual Turnover (MAT) for best three individual years out of last five financial years of the lead partner shall be at least 50% & for each other partners shall be at least 33% of the estimated cost. Sign & Seal of Bidder GETCO/E/TS-SDH/PDH FOTE/R1, Dt:16.04.2011 Page 50 of 60
TECHNICAL SPECIFICATION FOR SDH/PDH Equipment with integrated Access Multiplexer 3. If the bid is submitted for supply portion under Licensee/Licensor agreement , then the financial criteria under [B] 2 is to be satisfied considering Licensor as one of the JV partner ( Condition 3(II) of [A] shall be applicable). 4. Further, in case of the bid to be furnish as a JV/Consortium partners then the each JV/Consortium partners has to furnish 5% of the overall tender cost towards the B.G. in addition to the 10% of the Bank Guarantee to be submitted by the lead partner ( as security deposit). The terms, conditions & validity of all such BG’s shall be the same. 5. The bidder shall have to furnish a brief write-up, backed with adequate data, explaining his available capacity (both technical and financial such as profit loss statement, balance sheet, auditor’s report for last three years, bankers certificate etc.) for manufacture and supply of the required material, within the specified time of completion, after meeting all their current commitments when bid either as individual bidder or JV/Consortium and supply portion under Licensee/Licensor agreement. Copies of original documents defining the constitution or legal status, place of registration and principal place of business of the company shall also be submitted along with the bid. The owner may assess the capacity & capability of the bidders, to successfully execute the scope of work covered under the work with in stipulated completion period. This assessment shall inter-alia include. 1) Document verification 2) Bidders work/manufacturing facilities visit 3) Manufacturing capacity, details of work executed, works in hand, anticipated in future & the balance capacity available for the present scope of work 4) Details of testing facilities, manpower and financial resources 5) Details of quality system in place 6) Past experience & performance 7) Customer feed back 8) Banker’s feed back Additional Documents: Apart From various documents to be furnished along with the Bid as required in the GCC and ECC, the following documents/details are to be furnished by the Bidder: 1. Service Tax Registration No. date/ issuing authority. 2. Details of Partners/Directors of the Firm/Company. 3. Experience Record and details of orders pending / executed for Various Utilities 4. Solvency certificate from Bank (up to 20 % of Bid value). Sign & Seal of Bidder GETCO/E/TS-SDH/PDH FOTE/R1, Dt:16.04.2011 Page 51 of 60
Page 1 and 2: TECHNICAL SPECIFICATION FOR SDH/PDH
Page 49: TECHNICAL SPECIFICATION FOR SDH/PDH

Technical Specification for - Gujarat Electricity Board

Create successful ePaper yourself

Delete template?

Save as template?