Technical Specification for - Gujarat Electricity Board

More documents

Recommendations

Info

TECHNICAL SPECIFICATION FOR SDH/PDH Equipment with integrated Access Multiplexer 2.13 SPECIAL CONDITION TO BIDDER: 1 The installation & commissioning of FOTE equipments will require to be carried out stage wise depending on the readiness of the transmission lines with OPGW and building of Sub-stations between which lines will be terminated. Hence in the context of above bidder shall have to specify the special storage condition if required. 2. The bidder shall furnish the full technical details & drawings for the offered SDH (STM -1) equipment with integrated Access Multiplexer. 3. The testing of all FOTE equipments for stipulated requirements, ultimate system capacity supported as per technical specification complete with path protection and testing of signals for ring topology arrangement shall be responsibility of the bidder. Also the bidder shall have to ensure for correctness of the operation of the FOTE equipments which will require to be connected in ring topology for various applications viz. Speech and Data communication, teleportection signal transmission/reception and SCADA connectivity as per Technical Specification. 4. The successful bidder shall have to submit the documents covering the details of various tests to be done for each FOTE with procedure, test set up, connection diagram and table to record test results obtained against the required value of test parameter. 5. The bidder shall have to submit the working diagram for the NMS system comprising various nodes of the OPGW network: Network Layout (copy enclosed) showing connection diagram with details of interface port from central control stations to nodes of the network. 6. The bidder shall have to arrange for imparting training free of cost including cost of logistics and accommodation to at least TEN (10) technical official of GETCO covering complete installation & commissioning procedure, working functionality of different modules, supporting software installation & management (both EMS & NMS), Handling the equipments ( both hardware & software configuration), fault diagnosis & attending etc. In the event of order bidder shall have to get approval of training literature/documents from GETCO. 7. The bidder shall have to supply LCT – Local Craft terminal- 11 Nos., i.e. laptop (as per specification enclosed) along with EMS free of cost under this package. 8. After submission of bids, each bidder will have to make a detailed technical presentation (2 to 3 Hrs.) on the solution offered explaining advantages & disadvantages to GETCO authorities to enable GETCO to understand the complete offering by the bidder at no extra cost to GETCO. 9. Any deviation shall be clearly indicated separately. 10. The GETCO reserves right to increase or decrease the quantity at the time of placing the order. 11. The GETCO reserve right either to accept or reject any of the offers without assigning the reason. Sign & Seal of Bidder GETCO/E/TS-SDH/PDH FOTE/R1, Dt:16.04.2011 Page 52 of 60
TECHNICAL SPECIFICATION FOR SDH/PDH Equipment with integrated Access Multiplexer 2.14 SCHEDULE OF REQUIREMENT 2.14.1 The delivery of the material, in any case shall be finished within two quarters from date of order. 2.14.2 The consignee details shall be issued to the successful bidder/s after placement of orders and after inspection and testing of FOTE and all equipments, hardware & software of NMS and test instruments etc at manufacturer’s works. 2.15 SPARES The bidder shall furnish in his offer, unit rates for mandatory spares (as stated in Schedule of BOQ) and also for various types of SFPs, Boosters, Wave length translator (Given in table 2-4 here under) along with the price bid . Also, bidder shall have to provide the values for TX Power EOL, RX Sensitivity & Margin for each items of table 2-4 with the offer. Also bidder shall have to submit their offer for the spares other than specified in BOQ if required, with unit price separately. The purchaser reserves the right of selection of items and quantities of these spares to be ordered. The bidder is bound to supply spares for maintenance as and when required for service life of the FOTE & NMS as per clause No.2.2.5.10. SFP S1.1 SFP L1.1 SFP L1.2 SFP X1.2 SFP U1.2 OPTICAL BOOSTER OPTICAL WAVELENGTH TRANSLATOR Any other combinations which does not belongs to above but will require to be used by the bidder to meet the optical power budget requirement. TRANSMIT POWER EoL (dB) RECEIVER SENSITIVITY (dB) Margin 2.16 TESTS 2.16.1. Type test 2.16.1.1.The FOTE offered shall be fully KEMA type tested or type tested in NABL approved laboratory as per the relevant standards mentioned at clause No. 2.11. The bidder shall submit the complete type test reports for the offered FOTE along with the offer otherwise the offer shall be liable to be rejected. 2.16.1.2 The purchaser reserves the right to demand repetition of some or all the type test in the presence of the purchaser’s representative. For this purpose the bidder may quote unit rates for carrying out each type test. Sign & Seal of Bidder GETCO/E/TS-SDH/PDH FOTE/R1, Dt:16.04.2011 Page 53 of 60
Page 1 and 2: TECHNICAL SPECIFICATION FOR SDH/PDH
Page 51: TECHNICAL SPECIFICATION FOR SDH/PDH

Technical Specification for - Gujarat Electricity Board

Create successful ePaper yourself

Delete template?

Save as template?