mdp control series - Omega Engineering

More documents

Recommendations

Info

Parameter Confi guration: MD10P MD3P or MD3E P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 P1-8 P1-9 P1-10 P1-11 P1-12 N L A- A+ COM +5V S1 S2 NO C NC IN1 26 black red white NOT USED NOT USED NOT USED NOT USED *FUSE * Size fuse according to unit and application. See electrical specifications for maximums. } AC Line Input 85-265VAC, 50-60 Hz Speed 1 Select Speed 2 Select NC MOTOR Synchronized Conveyor Controller with Jog Switch Dart PU-2E or Equivalent Encoder Parameter Value Notes 10 2 Time Mode Setting (MM:SS is a time-based unit) 20 390 Display minimum set to 6:30 (MM:SS) For example: (6 minutes * 60 seconds-per-minute) + 30 seconds = 390 seconds 21 735 Display maximum set to 12:12 (MM:SS) For example: (12 minutes * 60 seconds-per-minute) + 15 seconds = 735 seconds 30 400 Display should indicate 6:40 (MM:SS) when motor at Reference RPM, parameter 31 For example: (6 minutes * 60 seconds-per-minute) + 40 seconds = 400 seconds 31 1380 This is the RPM at which the Display Reference, parameter 30, should be displayed 32 1 Pulses per revolution of shaft encoder or pickup is 1 PPR 35 7 Set S2 input mode to jog when low 36 530 Set fixed process time during jog to 8:50 (MM:SS) For example: (8 minutes * 60-seconds-per-minute) + 50 = 530 seconds Description: A synchronized conveyor system comprised of two conveyors with no mechanical linkage between them. The master conveyor is driven by a basic Dart analog DC motor <strong>control</strong>. The slave or follower conveyor should follow the master's position with exacting long-term accuracy. The slave conveyor should be able to be jogged into position when the master is stopped at a rate of 350 RPM. The slave conveyor may be adjusted from 90.0% to 110.0% of the master conveyor rate using the user interface.
Application Diagram: Master Side Follower Side MD10P MD3P or MD3E Box A Conveyor 1 Box B Conveyor 2 Dart PU-20E or equivalent Dart PU-10E or equivalent P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 P1-8 P1-9 P1-10 P1-11 P1-12 N L A- A+ 27 Belt DC Gear Motor Belt DC Gear Motor CONTROL Page COM +5V S1 S2 NO NOT USED C NOT USED NC NOT USED IN1 Jog Switch Ite m Valu Tach 100.0 MICRO-DRIVE ENTER Dart MD10P, MD3P, or MD3E Motor Control *FUSE black red white FOLLOWER MOTOR white red black * Size fuse according to unit and application. See electrical specifications for maximums. 2 4 6 Motor 0 10 Dart 253G or other Motor Control 8 CONTROLS Jog Switch Jog Run } AC Line Input 85-265VAC, 50-60 Hz ON OFF FOLLOWER PICK-UP MOUNTED TO MOTOR SHAFT Dart PU-10E or Equivalent Encoder MASTER PICK-UP MOUNTED TO MOTOR SHAFT Dart PU-2E or Equivalent Encoder
Page 1 and 2: MDP CONTROL SERIES LT61 (0709) CONT
Page 3 and 4: Table of Contents Introduction ....
Page 5 and 6: Model Table Model Available Options
Page 7 and 8: Installation and Mechanical Dimensi
Page 9 and 10: MD3E Mounting and Dimensions PU-E S
Page 11 and 12: MD3E P1-1 P1-2 P1-3 P1-4 P1-5 P1-6
Page 13 and 14: Test Procedure: Adjust the target (
Page 15 and 16: Parameter-Selection Mode can be ent
Page 17 and 18: Software Parameters, cont'd Paramet
Page 19 and 20: Parameter 14 - Keypad Mode This par
Page 21 and 22: Parameter 30 - Signal Input 1 (S1)
Page 23 and 24: Mode 4: Inhibit When UIN1 High (Not
Page 25 and 26: Mode 4: Silencing Enabled, Reset On
Page 27: Parameter Confi guration: Parameter
Page 31 and 32: Technical Support Options Troublesh

mdp control series - Omega Engineering

Create successful ePaper yourself

Delete template?

Save as template?