Owner's Manual EN Page 2 The above warning is located on the top ...

More documents

Recommendations

Info

Panel Operation Foreword Panel Operation Network Settings References Introduction to the SP2060 <strong>The</strong> Controls and Connectors X-OVER (Crossover) Setting the Crossover Input signals can be divided into specified frequency ranges to suit speaker response character<strong>is</strong>tics prior to output. <strong>The</strong> number of div<strong>is</strong>ion <strong>is</strong> determined to 1-way through 6- way, depending on the selected component. Parameter Range Function LEVEL POLARITY HPF LPF –∞, –138.00 through +10.00dB NORMAL INVERTED Refer to Step 4. Adjusts the level of the signal input to the Crossover. <strong>The</strong> same Level setting <strong>is</strong> used for the output channels of a component. <strong>The</strong> output signal phase for each frequency range <strong>is</strong> inverted. 1. Press the [X-OVER] key repeatedly until the X- Over d<strong>is</strong>play appears on the screen. OUT 1 FREQ LPF = 20.0kHz 2. Press the [SEL] key for the target Output channel. <strong>The</strong> [SEL] key LED of the selected channel lights up, and the corresponding channel name <strong>is</strong> d<strong>is</strong>played. OUT 3 FREQ LPF = 20.0kHz 3. Press the [NEXT]/[BACK] keys to select a parameter to edit. OUT 3 LPF TYPE =24AdjustGc 4. Press the [▲INC]/[▼DEC] keys to set the parameter value. Parameter Range Function HPF LPF TYPE FREQ (Frequency) Gc TYPE FREQ (Frequency) Gc Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz 20.0Hz–20.0kHz –6dB through +6dB Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz 20.0Hz–20.0kHz –6dB through +6dB Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. Specifies the cutoff frequency of the high pass filter. You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. Specifies the cutoff frequency of the low pass filter. You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. 28 SP2060 Owner’s <strong>Manual</strong>
Panel Operation NOTE • <strong>The</strong> type names are abbreviated on the SP2060 screen. For example, “24dB/Oct Bessel” <strong>is</strong> d<strong>is</strong>played as “24Bessel.” • Gc page <strong>is</strong> d<strong>is</strong>played if you select “Adjust Gc” for the Type parameter. LIBRARY Using libraries facilitates the recall of optimal speaker settings. Up to 60 libraries are available for each component via the DME Designer application. Foreword • Thru No filter <strong>is</strong> applied. <strong>The</strong> original character<strong>is</strong>tics are kept with no attenuation for all frequency ranges. • AdjustGc (Adjustable Gc) Filters with an Adjustable Gc enable you to adjust the gain at the cutoff frequency in the range of –6dB through +6dB. With Gc set to –3dB, the filter <strong>is</strong> practically a Butterworth filter. And with Gc set to –6dB, the filter <strong>is</strong> practically a Linkwitz-Riley filter. • Butrwrth (Butterworth) Th<strong>is</strong> filter <strong>is</strong> the most common type of filter. It has a flat pass band and a –3dB gain at the cutoff frequency. • Bessel Th<strong>is</strong> filter focuses on the phase character<strong>is</strong>tics. Although it has a more gradual roll-off than a Butterworth filter, it will pass a square wave without causing ringing. • Linkwitz (Linkwitz-Riley) Th<strong>is</strong> filter features the square of the second order. When the output signal from its LPF and HPF are combined, the gain over the entire range <strong>is</strong> +/–0dB. It has a flat pass band and a –6dB gain at the cutoff frequency. D<strong>is</strong>playing the current library Pressing the [X-OVER] key repeatedly will select the Current Library d<strong>is</strong>play, Library L<strong>is</strong>t d<strong>is</strong>play, or X-Over d<strong>is</strong>play, in th<strong>is</strong> order. <strong>The</strong> title of the library most recently recalled for each component will be d<strong>is</strong>played. NOTE Recalling a library CURR<strong>EN</strong>T LIBRARY IF2112/95 Libraries cannot be d<strong>is</strong>played or recalled for Input channels. If you press an Input channel [SEL] key, a message appears. Follow the steps below to recall a library: 1. Press the [X-OVER] key repeatedly until the Library L<strong>is</strong>t d<strong>is</strong>play appears on the screen. LIBRARY LIST IF2112/64 2. Press the [SEL] key of an Output channel for a component for which you w<strong>is</strong>h to recall a library. 3. Press the [▲INC]/[▼DEC] keys to select a library. Introduction to the SP2060 <strong>The</strong> Controls and Connectors Network Settings Panel Operation LIBRARY LIST IF2112/64 4. Press the [NEXT/RECALL] key. A confirmation message will appear. References LIBRARY RECALL ARE YOU SURE SP2060 Owner’s <strong>Manual</strong> 29
Page 1 and 2: Owner’s Manual <
Page 3 and 4: 1. IMPORTANT NOTICE: DO NOT MODIFY
Page 5 and 6: Handling caution • Do not use the
Page 7 and 8: Foreword Thank you for purchasing t
Page 9 and 10: Introduction to the SP2060 Features
Page 11 and 12: Introduction to the SP2060 2 x (2-w
Page 13 and 14: Introduction to the SP2060 2 x 3-wa
Page 15 and 16: Introduction to the SP2060 5-way +
Page 17 and 18: Introduction to the SP2060 Multi Zo
Page 19 and 20: Introduction to the SP2060 Zone pro
Page 21 and 22: Introduction to the SP2060 Routing
Page 23 and 24: The Controls and C
Page 25 and 26: Panel Operation DELAY You can set t
Page 27: Panel Operation ROUTING Input routi
Page 31 and 32: Panel Operation Scenes are stored i
Page 33 and 34: Panel Operation 5. Press the [NEXT]
Page 35 and 36: Panel Operation Setting the User Lo
Page 37 and 38: Panel Operation Dis</strong
Page 39 and 40: Network Settings This</stro
Page 41 and 42: Network Settings Viewing the MAC Ad
Page 43 and 44: References Libraries for 1-way spea
Page 45 and 46: References Target speakers Library
Page 47 and 48: References Status messages Referenc
Page 49 and 50: References Crosstalk@1KHz Fs=96kHz
Page 51 and 52: References Dimensions References 36
Page 53 and 54: References Library ................
Page 55 and 56: For details of products, please con

Owner's Manual EN Page 2 The above warning is located on the top ...

Create successful ePaper yourself

Delete template?

Save as template?