Owner's Manual EN Page 2 The above warning is located on the top ...

References
Crosstalk@1KHz
Fs=96kHz
Input Output Conditions MIN TYP MAX Units
Foreword
INPUT A OUTPUT 2, 4, 6
INPUT B OUTPUT 1, 3, 5
INPUT A assigned to OUTPUT 1, 3 or 5
INPUT B assigned to OUTPUT 2, 4 or 6
INPUT A assigned to OUTPUT 1, 3 or 5
INPUT B assigned to OUTPUT 2, 4 or 6
–80 dB
–80 dB
*Crosstalk <strong>is</strong> measured with a 18dB/octave filter @80kHz.
LED Level Meters
Metering points Conditions MIN TYP MAX Units
OVER red LED: On 0 dBFS
Introduction
to the SP2060
–6 amber LED: On –6 dBFS
INPUT A, B
–12 amber LED: On –12 dBFS
–18 amber LED: On –18 dBFS
OUTPUT 1–6
–30 green LED: On –30 dBFS
–48 green LED: On –48 dBFS
OVER red LED: On 0 dBFS
LIMIT amber LED: On
LIMIT*
–6 green LED: On –6 dBFS
–12 green LED: On –12 dBFS
<strong>The</strong> Controls
and Connectors
–18 green LED: On –18 dBFS
–40 green LED: On –40 dBFS
*<strong>The</strong> LED turns on when the internal limiter <strong>is</strong> activated.
Input/Output Character<strong>is</strong>tics
Analog Input Character<strong>is</strong>tics
Input Terminals
Actual Load
Impedance
Analog Output Character<strong>is</strong>tics
For Use With
Nominal
Nominal
Input level
Max. before clip
Connector
INPUT A, B 10 k Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-31 type (balanced) *1
*1. XLR-3-31 type connectors with latches are balanced. (1=GND, 2=HOT, 3=COLD)
*2. In these specifications, 0 dBu <strong>is</strong> referenced to 0.775 Vrms.
*3. All AD converters are 24-bit linear, 64-times oversampling. (Fs=96kHz)
Output
Terminals
Actual Load
Impedance
For Use With
Nominal
Nominal
Input level
Max. before clip
Connector
OUTPUT 1–6 75 Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-32 type (balanced) *1
*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2. In these specifications, 0 dBu <strong>is</strong> referenced to 0.775 Vrms.
*3. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz) or 64-times oversampling (Fs=96kHz).
Network Settings Panel Operation
References
Digital Input Character<strong>is</strong>tics
Terminal Format Data length Level Connector
DIGITAL INPUT AES/EBU AES/EBU 24 bit RS422 XLR-3-31 type (balanced) *1 *2
*1. XLR-3-31 type connector with latch <strong>is</strong> balanced. (1=GND, 2=HOT, 3=COLD)
*2. Only Double Speed Format <strong>is</strong> supported at 96 kHz. Double Channel or Single Format <strong>is</strong> not supported.
SP2060 Owner’s <strong>Manual</strong> 49