condair sH2

More documents

Recommendations

Info

40 Models “REflow C” and “REflow SC” R 3/4" Water connection unit (accessory) Water filter Pressure reducing valve Shut-off valve Water supply 2...10 bar 5...45 °C ø 40/34 mm Drain line with constant down-slope Siphon (building side, height adjusted to the duct pressure) Open funnel (building side)
41 4.3.2 Notes on water installation Water supply The water supply is to be carried out according to the figure found in chapter 4.3.1 and the applicable local regulations for water installations. The indicated connection specifications must be observed. – The installation of the shut-off valve, pressure reducing valve and a water filter should be made as close as possible to the unit. – Notes on water quality: – For the water supply of the Condair SH2, use exclusively untreated drinking water, fully demineralised water or partly softened water with a max of 100 cfu/ml. – The use of additives such as corrosion inhibitors, disinfectants, etc. is not allowed, since these additives may endanger health and affect proper operation. – If the Condair SH2 shall be operated with softened water, please contact your Condair supplier. – The connection material must be pressure-proof and certified for use in drinking water supply systems. – Important! Before connecting the water line to the unit, the line must be flushed thoroughly. CAUTION! The thread at the humidifier connection is made of plastic. To avoid overtightening, the union nut of the water pipe must be tightened by hand only. Water drain The water drain is to be carried out according to the figure found in chapter 4.3.1 and the applicable local regulations for water installations. The indicated connection specifications must be observed. – Make sure the drain line is installed with a constant down-slope to the siphon of the building. – Make sure the drain pipe is correctly fixed and easily accessible for inspections and cleaning purposes. – The minimum inside diameter of the drain pipe of 34 mm must be maintained throughout the entire length! When operating the Condair SH2 with fully demineralised water: Fully demineralised water is aggressive! For this reason, use exclusively plastic or stainless steel installation materials (min. DIN 1.4301).
Page 1: Condair SH2 Adiabatic Humidifiers I
Page 4 and 5: 1 Introduction 1.1 To the very begi
Page 6 and 7: 2 For your safety General Every per
Page 8 and 9: 3 Product overview 3.1 Model overvi
Page 10 and 11: 10 3.3 Model “flow” 3.3.1 Const
Page 12 and 13: 12 3.4 Model “flow C” 3.4.1 Con
Page 14 and 15: 14 3.5 Model “flow SC” 3.5.1 Co
Page 16 and 17: 16 3.6 Model “REflow” 3.6.1 Con
Page 18 and 19: 18 3.7 Model “REflow C” 3.7.1 C
Page 20 and 21: 20 3.8 Model “REflow SC” 3.8.1
Page 22 and 23: 22 To prevent accumulation of miner
Page 24 and 25: 24 - We recommend to install air fi
Page 26 and 27: 26 D E Hint: With close space condi
Page 28 and 29: 28 G 5. Fix the front bracket “G
Page 30 and 31: 30 7. The air gap between the outer
Page 32 and 33: 32 flow flow C flow SC REflow REflo
Page 34 and 35: 34 11. Only for units with mist eli
Page 36 and 37: 36 13. Mounting the trickling hoods
Page 38 and 39: 38 4.3 Water installation 4.3.1 Ove
Page 42 and 43: 42 4.4 Electric installation Note:
Page 44 and 45: 44 4.4.3 Wiring diagram Condair SH2
Page 46 and 47: 46 4.4.5 Wiring diagram Condair SH2
Page 48 and 49: 48 5 Operation 5.1 Putting into ope
Page 50 and 51: 50 6 Maintenance 6.1 Important note
Page 52 and 53: 52 Water installation Check water t
Page 54 and 55: 54 6.4.2 Dismantle and install the
Page 56 and 57: 56 7.2 Notes on fault elimination D
Page 58 and 59: 58 9 Product specifications 9.1 Tec
Page 60 and 61: Notes
Page 62 and 63: Notes
Page 64: Consulting, Sales and Service: Solu

condair sH2

Create successful ePaper yourself

Delete template?

Save as template?