DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

More documents

Recommendations

Info

4. Stitching Head 1. Pass the wire between the 1 wire guide pins. 2. Pass the wire through the two 3 felts and through the 2 wire return stopper unit. 3. Set the 8 Triangular knob at the no stitching position, insert the wire into the tip of the 6 Upper wire tube. Make sure the wire is not deformed. 16 4-3. Setting the Wire Stitching Wire 2 wire return stopper unit 8 Triangular knob Wire guide pin Wire 3 Felts 6 Upper wire tube No stitching
4. Insert the wire from the 2 Upper wire tube, and feed it gently inside using the pliers provided until the tip of the wire reaches the bk Lower wire tube. Make sure the wire is not deformed. 5. Set the 8 Triangular knob at the stitching position. 6. Press the bq Adjusting handle against the head of the 9 Feed wheel and rotate it clockwise, and feed the wire out. Rotate the adjusting handle twice. Note If the wire is bent, it will not go into the bk lower wire tube and will jam. Pull out the wire, cut off the bent part, and set again. 9Feed wheel bk Lower wire tube 9 Feed wheel Stitching Wire bkLower wire tube 8 Triangular knob 4. Stitching Head 6 Upper wire tube No stitching bq Adjusting handle 17
Page 1 and 2: System 4000 DYNAMIC BOOKLET MAKER D
Page 3 and 4: INTRODUCTION Thank you for purchasi
Page 5 and 6: CAUTIONS: Do not use flammable spra
Page 7 and 8: 2. Usage Precautions 2-1. Power Sup
Page 9 and 10: 1 Entrance Section 3-2. Internal Pa
Page 11 and 12: 3 Folding Section ep 3. Names and F
Page 13 and 14: Control Panel 2 1 Lamps/Displays 1
Page 15 and 16: Operation Keys Display Function bmS
Page 17: No. Name Function 1 2 3 4 5 6 7 8 9
Page 21 and 22: 1. Rotate the 8 triangular knob to
Page 23 and 24: 5. Stitching Range Stitching Positi
Page 25 and 26: 6. Stitching Normal Size Paper Do n
Page 27 and 28: 6.Stitching Normal Size Paper 5. Ad
Page 29 and 30: 6-1-4 Points to remember when paper
Page 31 and 32: 6. Stitching Normal Size Paper 6-2.
Page 33 and 34: 4) • The unit selected at 3) will
Page 35 and 36: 6-6. After Starting To finely adjus
Page 37 and 38: 7. Memorizing • The bs Memory Inp
Page 39 and 40: 5) • Press bl Select Fold Key and
Page 41 and 42: 10) • Input the length [S] from t
Page 43 and 44: • To change the input, input the
Page 45 and 46: 8) • Using the 7 Numerical Keys,
Page 47 and 48: When Corner-Stitching at Right Side
Page 49 and 50: 8-4. No-Stitching No-Folding Use th
Page 51 and 52: 2 Attaching Conditions A m ? Attach
Page 53 and 54: If the paper skews immediately afte
Page 55 and 56: 5 Loosen the knob screw at (D), and
Page 57 and 58: 9-8. Using the Guides After Folding
Page 59 and 60: 3 Adjusting the press rollers 3 lev
Page 61 and 62: 10. Using Function Keys Operating t
Page 63 and 64: • Pressing 7 of the 7 Numerical K
Page 65 and 66: 12. LCD Error Messages and Correspo
Page 67 and 68: • Display when the paper jam has
Page 69 and 70:
13. The Unit will Stop in These Cas
Page 71 and 72:
15. Maintenance of the Stitching He
Page 73 and 74:
This page is a blank page.
Page 75 and 76:
This page is a blank page.
show all

DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

Create successful ePaper yourself

Delete template?

Save as template?