DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

More documents

Recommendations

Info

8. Numerically Inputting the Paper Size 8) • Input the width of the paper (W) as shown below. 38 • Using the 7 Numerical Keys, input four digits. Example) Press the 7 Numerical Keys in the following order. 0 9 2 0 However, input a value (W) between 8.27 and 14inch. Note To clear the input number to 0, press the 8 Clear Key. To return to the most recent input mode, press the 3 Escape Key. 9) • When the 9 Set Key is pressed, the LCD displays [*5.S=06.80]. [S] is the length from the saddle stitching stopper to the stitching position. *5. S=06.80 Paper feeding direction F 1 2 3 C 4 5 6 0 7 8 9 F 1 2 3 C 4 5 6 0 7 8 9 9 W
10) • Input the length [S] from the saddle stitching stopper to the stitching position. • The length is automatically calculated (from 1:1) [L x 1/2], and the LCD displays [*5. S=06.80]. • To change the input, input the four digits again using the 7 Numerical Keys. The range is S=5.51 inch to the smaller value of L– 5.51 inch or 8.86inch. 11) • Press the 9 Set Key once. The LCD displays [*5. A=02.30]. 8. Numerically Inputting the Paper Size *5. A=02.30 Stitching position Paper feeding direction S F 1 2 3 C 4 5 6 0 7 8 9 F 1 2 3 C 4 5 6 0 7 8 9 9 39
Page 1 and 2: System 4000 DYNAMIC BOOKLET MAKER D
Page 3 and 4: INTRODUCTION Thank you for purchasi
Page 5 and 6: CAUTIONS: Do not use flammable spra
Page 7 and 8: 2. Usage Precautions 2-1. Power Sup
Page 9 and 10: 1 Entrance Section 3-2. Internal Pa
Page 11 and 12: 3 Folding Section ep 3. Names and F
Page 13 and 14: Control Panel 2 1 Lamps/Displays 1
Page 15 and 16: Operation Keys Display Function bmS
Page 17 and 18: No. Name Function 1 2 3 4 5 6 7 8 9
Page 19 and 20: 4. Insert the wire from the 2 Upper
Page 21 and 22: 1. Rotate the 8 triangular knob to
Page 23 and 24: 5. Stitching Range Stitching Positi
Page 25 and 26: 6. Stitching Normal Size Paper Do n
Page 27 and 28: 6.Stitching Normal Size Paper 5. Ad
Page 29 and 30: 6-1-4 Points to remember when paper
Page 31 and 32: 6. Stitching Normal Size Paper 6-2.
Page 33 and 34: 4) • The unit selected at 3) will
Page 35 and 36: 6-6. After Starting To finely adjus
Page 37 and 38: 7. Memorizing • The bs Memory Inp
Page 39: 5) • Press bl Select Fold Key and
Page 43 and 44: • To change the input, input the
Page 45 and 46: 8) • Using the 7 Numerical Keys,
Page 47 and 48: When Corner-Stitching at Right Side
Page 49 and 50: 8-4. No-Stitching No-Folding Use th
Page 51 and 52: 2 Attaching Conditions A m ? Attach
Page 53 and 54: If the paper skews immediately afte
Page 55 and 56: 5 Loosen the knob screw at (D), and
Page 57 and 58: 9-8. Using the Guides After Folding
Page 59 and 60: 3 Adjusting the press rollers 3 lev
Page 61 and 62: 10. Using Function Keys Operating t
Page 63 and 64: • Pressing 7 of the 7 Numerical K
Page 65 and 66: 12. LCD Error Messages and Correspo
Page 67 and 68: • Display when the paper jam has
Page 69 and 70: 13. The Unit will Stop in These Cas
Page 71 and 72: 15. Maintenance of the Stitching He
Page 73 and 74: This page is a blank page.
Page 75 and 76: This page is a blank page.

DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?