DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

More documents

Recommendations

Info

The DBM-400 Sheet by Sheet (SxS) conforms with FCC regulations only when used in the following system configurations. <strong>System</strong>1:DB-10+DR-14+DBM-400 SxS+DBM-400T+DBM-400LS+DBM-400K <strong>System</strong>2:DB-10+DB-10TR+DBM-400 SxS+DBM-400T+DBM-400LS+DBM-400K • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
INTRODUCTION Thank you for purchasing a DBM-400 sheet by sheet SxS. To ensure correct usage, please read this instruction manual thoroughly, especially the section “Safety Precautions”. After reading, please keep this instruction manual handy for future reference. CONTENTS 1. Safety Precautions .............................2 2. Usage Precautions .............................5 2-1. Power Supply .................................................... 5 2-2. Operating Environment ..................................... 5 2-3. Storage Conditions ........................................... 5 2-4. Maintenance ..................................................... 5 3. Names and Functions of the Parts ...6 3-1. External View .................................................... 6 3-2. Internal Parts..................................................... 7 3-3. Control Panel .................................................. 11 4. Stitching Head ..................................14 4-1. Names and Functions of Parts........................ 14 4-2. Wire................................................................. 15 4-3. Setting the Wire .............................................. 16 4-4. How to Stitch Tests ......................................... 18 4-5. Removing Wires.............................................. 19 4-6. Adjusting Parts ................................................ 20 5. Stitching Range ................................21 6. Stitching Normal Size Paper ...........23 6-1. Before Starting ................................................ 23 6-2. Saddle-Stitching Double Letter and Letter Paper ........................................................................ 29 6-3. Side-Stitching Letter Paper (No Folding) ........ 30 6-4. Fine Adjustment in Step Mode ........................ 30 6-5. Other Functions .............................................. 32 6-6. After Starting ................................................... 33 6-7. After Completing Operations........................... 34 7. Memorizing .......................................35 8. Numerically Inputting the Paper Size ... 36 8-1. Saddle-Stitching and Folding .......................... 36 8-2. Side-Stitching .................................................. 42 8-3. Corner-Stitching .............................................. 44 8-4. No-Stitching No-Folding .................................. 47 9. Binding ..............................................48 9-1. Using the Auxiliary Roller Stay ........................ 48 9-2. Using the Auxiliary Roller Unit ........................ 50 9-3. Using the Paper Ejection Roller Unit............... 51 9-4. Using the Paper Guide.................................... 52 9-5. Using the Back Stopper and Roller ................. 53 9-6. Using the Stitching Stopper and Folding Stopper............................................... 54 9-7. Using the Folding Guide (For Folding) ............ 54 9-8. Using the Guides After Folding ....................... 55 9-9. Using the Press Roller .................................... 56 9-10. Using the Belt Stacker Unit ............................. 57 10. Using Function Keys........................59 11. Precautions Using Emergency Stop Switch ................................................62 12. LCD Error Messages and Corresponding Actions to Take ......63 12-1. Error Messages..............................................63 12-2. Paper Jam Display.........................................64 12-3. Serious Problems...........................................65 12-4. Other Messages.............................................66 13. The Unit will Stop in These Cases ..67 14. Cleaning ............................................68 15. Maintenance of the Stitching Head.69 16. Specifications ...................................70 1
Page 1: System 4000 DYNAMIC BOOKLET MAKER D
Page 5 and 6: CAUTIONS: Do not use flammable spra
Page 7 and 8: 2. Usage Precautions 2-1. Power Sup
Page 9 and 10: 1 Entrance Section 3-2. Internal Pa
Page 11 and 12: 3 Folding Section ep 3. Names and F
Page 13 and 14: Control Panel 2 1 Lamps/Displays 1
Page 15 and 16: Operation Keys Display Function bmS
Page 17 and 18: No. Name Function 1 2 3 4 5 6 7 8 9
Page 19 and 20: 4. Insert the wire from the 2 Upper
Page 21 and 22: 1. Rotate the 8 triangular knob to
Page 23 and 24: 5. Stitching Range Stitching Positi
Page 25 and 26: 6. Stitching Normal Size Paper Do n
Page 27 and 28: 6.Stitching Normal Size Paper 5. Ad
Page 29 and 30: 6-1-4 Points to remember when paper
Page 31 and 32: 6. Stitching Normal Size Paper 6-2.
Page 33 and 34: 4) • The unit selected at 3) will
Page 35 and 36: 6-6. After Starting To finely adjus
Page 37 and 38: 7. Memorizing • The bs Memory Inp
Page 39 and 40: 5) • Press bl Select Fold Key and
Page 41 and 42: 10) • Input the length [S] from t
Page 43 and 44: • To change the input, input the
Page 45 and 46: 8) • Using the 7 Numerical Keys,
Page 47 and 48: When Corner-Stitching at Right Side
Page 49 and 50: 8-4. No-Stitching No-Folding Use th
Page 51 and 52: 2 Attaching Conditions A m ? Attach
Page 53 and 54:
If the paper skews immediately afte
Page 55 and 56:
5 Loosen the knob screw at (D), and
Page 57 and 58:
9-8. Using the Guides After Folding
Page 59 and 60:
3 Adjusting the press rollers 3 lev
Page 61 and 62:
10. Using Function Keys Operating t
Page 63 and 64:
• Pressing 7 of the 7 Numerical K
Page 65 and 66:
12. LCD Error Messages and Correspo
Page 67 and 68:
• Display when the paper jam has
Page 69 and 70:
13. The Unit will Stop in These Cas
Page 71 and 72:
15. Maintenance of the Stitching He
Page 73 and 74:
This page is a blank page.
Page 75 and 76:
This page is a blank page.
show all

DUPLO CORPORATION System 4000 DYNAMIC ... - Godar Machinery

Create successful ePaper yourself

Delete template?

Save as template?