Mechanized Plasmarc Cutting Torch - ESAB Welding & Cutting ...

More documents

Recommendations

Info

Be sure this information reaches the operator. You can get extra copies through your supplier. caution These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and safe practices for arc welding and cutting equipment, we urge you to read our booklet, “Precautions and Safe Practices for Arc Welding, Cutting, and Gouging,” Form 52-529. Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate this equipment until you have read and fully understand these instructions. If you do not fully understand these instructions, contact your supplier for further information. Be sure to read the Safety Precautions before installing or operating this equipment. USER RESPONSIBILITY This equipment will perform in conformity with the description thereof contained in this manual and accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone or written request for service advice be made to the Authorized Distributor from whom it was purchased. This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility designated by the manufacturer. READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING. PROTECT YOURSELF AND OTHERS! 2
table of contents Section / Title Page 1.0 Safety Precautions ....................................................................................5 1.1 Safety - English ..................................................................................5 1.2 Safety - Spanish .................................................................................9 1.3 Safety - French .................................................................................13 2.0 Description ..........................................................................................17 2.1 General ........................................................................................17 2.2 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 2.3 Package Options Available .....................................................................17 2.4 Optional Accessories: ...........................................................................17 2.5 PT-36 Technical Specifications...................................................................21 3.0 Installation.......................................................................................... 23 3.1 Connection of Torch To Plasma System ......................................................... 23 3.2 Mounting Torch to Machine ................................................................... 25 4.0 Operation ...........................................................................................27 4.1 Set Up......................................................................................... 29 4.2 Cut Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.3 Torch Flow Passages .......................................................................... 34 5.0 Maintenance.........................................................................................35 5.1 Introduction ..................................................................................35 5.2 Torch Front End Disassembly................................................................... 36 5.3 Torch Front End Disassembly (for Production Thick Plate)........................................ 39 5.4 Assembly of Torch Front End ....................................................................42 5.5 Assembly of Torch Front End (for Production Thick Plate) ........................................ 43 5.6 Torch Body maintenance ..................................................................... 45 5.7 Removal and Replacement of the Torch Body ................................................... 46 5.8 Reduced Consumable Life .................................................................... 48 6.0 Replacement Parts ...................................................................................53 6.1 General ........................................................................................53 6.2 Ordering .......................................................................................53 3
Page 1: PT-36 Mechanized Plasmarc Cutting T
Page 5 and 6: section 1 safety precautions 1.0 Sa
Page 7 and 8: section 1 safety precautions 5. WAR
Page 9 and 10: section 1 1.2 Safety - Spanish ADVE
Page 11 and 12: section 1 sEGURIDAD 5. ADVERTENCIA-
Page 13 and 14: section 1 13 sÉCURITÉ 1.3 Safety
Page 15 and 16: section 1 sÉCURITÉ 5. AVERTISSEME
Page 17 and 18: section 2 Description 2.1 General T
Page 19 and 20: section 2 Description PT-36 200A St
Page 21 and 22: section 2 Description 2.5 PT-36 Tec
Page 23 and 24: section 3 Installation 3.1 Connecti
Page 25 and 26: section 3 Installation 3.2 Mounting
Page 27 and 28: section 4 operation WARNING Oil And
Page 29 and 30: section 4 operation 4.1 Set Up •
Page 31 and 32: section 4 operation 4.2.3. Cut Flat
Page 33 and 34: section 4 caution operation Recomme
Page 35 and 36: section 5 Maintenance 5.1 Introduct
Page 37 and 38: section 5 Maintenance 4. Unscrew no
Page 39 and 40: section 5 Maintenance 5.3 Torch Fro
Page 41 and 42: section 5 Maintenance 7. Remove ele
Page 43 and 44: section 5 Maintenance 5.5 Assembly
Page 45 and 46: section 5 Maintenance 5.6 Torch Bod
Page 47 and 48: section 5 Maintenance 3. Unwrap the
Page 49 and 50: section 5 Maintenance Checking for
Page 51 and 52: section 5 Problem: Failure to start
Page 53 and 54:
section 6 replacement parts 6.0 Rep
Page 55 and 56:
section 6 replacement parts 20 7 13
Page 57 and 58:
section 6 replacement parts 31 37 4
Page 59 and 60:
section 6 replacement parts 59
Page 61 and 62:
section 6 replacement parts PT-36 M
Page 63 and 64:
section 6 replacement parts Torch M
Page 65 and 66:
notes 65
Page 67 and 68:
evision history 1. Original release
show all

Mechanized Plasmarc Cutting Torch - ESAB Welding & Cutting ...

Create successful ePaper yourself

Delete template?

Save as template?