Mechanized Plasmarc Cutting Torch - ESAB Welding & Cutting ...

More documents

Recommendations

Info

section 4 operation caution Before attempting ANY corrections, check cutting variables with the factory recommended settings/consumable part numbers listed in Process Data. 4.2.2. Cut Angle Negative Cut Angle Top dimension is greater than the bottom. • • • • • Misaligned torch Bent or warped material Worn or damaged consumables Standoff low (arc voltage) <strong>Cutting</strong> speed slow (machine travel rate) Part Drop Part Positive Cut Angle Top dimension is less than the bottom dimension. • • • • • • Misaligned torch Bent or warped material Worn or damaged consumables High standoff High (arc voltage) <strong>Cutting</strong> speed fast Current high or low. (See Process Data for recommended current level for specific nozzles). Part Drop Part 30
section 4 operation 4.2.3. Cut Flatness Top And Bottom Rounded. Condition usually occurs when material is .25" thick (6,4mm) or less. • High current for given material thickness (See Process Data for proper settings). Drop Part Top Edge Undercut • Standoff low (Arc Voltage) Drop Part 31
Page 1 and 2: PT-36 Mechanized Plasmarc Cutting T
Page 3 and 4: table of contents Section / Title P
Page 5 and 6: section 1 safety precautions 1.0 Sa
Page 7 and 8: section 1 safety precautions 5. WAR
Page 9 and 10: section 1 1.2 Safety - Spanish ADVE
Page 11 and 12: section 1 sEGURIDAD 5. ADVERTENCIA-
Page 13 and 14: section 1 13 sÉCURITÉ 1.3 Safety
Page 15 and 16: section 1 sÉCURITÉ 5. AVERTISSEME
Page 17 and 18: section 2 Description 2.1 General T
Page 19 and 20: section 2 Description PT-36 200A St
Page 21 and 22: section 2 Description 2.5 PT-36 Tec
Page 23 and 24: section 3 Installation 3.1 Connecti
Page 25 and 26: section 3 Installation 3.2 Mounting
Page 27 and 28: section 4 operation WARNING Oil And
Page 29: section 4 operation 4.1 Set Up •
Page 33 and 34: section 4 caution operation Recomme
Page 35 and 36: section 5 Maintenance 5.1 Introduct
Page 37 and 38: section 5 Maintenance 4. Unscrew no
Page 39 and 40: section 5 Maintenance 5.3 Torch Fro
Page 41 and 42: section 5 Maintenance 7. Remove ele
Page 43 and 44: section 5 Maintenance 5.5 Assembly
Page 45 and 46: section 5 Maintenance 5.6 Torch Bod
Page 47 and 48: section 5 Maintenance 3. Unwrap the
Page 49 and 50: section 5 Maintenance Checking for
Page 51 and 52: section 5 Problem: Failure to start
Page 53 and 54: section 6 replacement parts 6.0 Rep
Page 55 and 56: section 6 replacement parts 20 7 13
Page 57 and 58: section 6 replacement parts 31 37 4
Page 59 and 60: section 6 replacement parts 59
Page 61 and 62: section 6 replacement parts PT-36 M
Page 63 and 64: section 6 replacement parts Torch M
Page 65 and 66: notes 65
Page 67 and 68: evision history 1. Original release

Mechanized Plasmarc Cutting Torch - ESAB Welding & Cutting ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?