1998 Dishwashers Intro - Whirlpool

More documents

Recommendations

Info

Removing the Soil Settler Assembly 1. Disconnect the dishwasher from the household electrical system and lay the unit on its back. 2. Remove the four (4) Hex-head screws securing the soil settler assembly to the tub. 3. Disconnect the two (2) hoses from the soil settler collector. 4. Remove the funnel and funnel grate, check valve ball and seal from the soil settler collector. (Fig. 1-11) FUNNEL GRATE FUNNEL CHECK VALVE BALL SEAL CLAMPS HOSE Removing the Heater Element Fig. 1-11 1. Disconnect the dishwasher from the household electrical system. 2. Disconnect the wiring harness connectors from the heater element terminals with a pair of needlenose pliers. 3. Remove the two long Hex-head nuts securing the heater element to the tub. (Fig. 1-12) 4. Remove the heater element from the three (3) metal clips that hold it suspended inside the tub. (Fig. 1-13) HEATER ELEMENT RETAINING NUTS HEATER ELEMENT Fig. 1-12 Fig. 1-13 6
Removing the Water Inlet Valve 1. Turn off the water supply to the dishwasher. 2. Turn the timer knob clockwise to the NORMAL WASH position to energize the water inlet valve and relieve water pressure in the line. 3. Turn the electrical supply to the dishwasher off and remove the toe panel and access panel. (Fig. 1-14) Fig. 1-14 4. Disconnect the wiring harness connector from the water inlet valve terminals. (Fig. 1-15) Fig. 1-15 5. Disconnect the water lines from the water inlet valve. 6. Remove the Hex-head screw securing the water inlet valve to the tub support assembly. Removing the Thermal Fuse 1. Turn the electrical supply to the dishwasher off and remove the toe panel and access panel. 2. Disconnect the orange and white wires from the thermal fuse terminals. (Fig. 1-16) 3. Remove the Hex-head screw securing the thermal fuse to the tub and remove the thermal fuse from the dishwasher. Removing the Float Switch THERMAL FUSE Fig. 1-16 ORANGE WIRE WHITE WIRE RETAINING SCREW 1. Turn the electrical supply to the dishwasher off and remove the toe panel and access panel. 2. Remove the Hex-head screw securing the float switch to the tub. (Fig. 1-17) 3. Lift the float from the housing inside the tub. 4. Unsnap the float switch housing cover and disconnect the two (2) wires from the terminals of the switch. (Fig. 1-18) FLOAT SWITCH HOUSING RETAINING SCREW Fig. 1-17 Fig. 1-18 TERMINALS WIRES SWITCH COVER 7
Page 1 and 2: CONSUMER SERVICES TECHNICAL EDUCATI
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION. . .
Page 5 and 6: Section One DURAWASH MODELS WITH SO
Page 7 and 8: COMPONENT ACCESS ! WARNING ELECTRIC
Page 9: 4. Disconnect the drain hose from t
Page 13 and 14: Removing the Timer 1. Disconnect th
Page 15 and 16: Fig. 1-28 Fig. 1-29 Fig. 1-30 Fig.
Page 17 and 18: SOLUTIONS TO COMMON PROBLEMS DIAGNO
Page 19 and 20: TROUBLESHOOTING GUIDE PRECAUTIONS T
Page 21 and 22: Cycle Timing Chart 17
Page 31 and 32: Section Two POWER CLEAN FILTER MODE
Page 33 and 34: Removing the Heater Element From be
Page 35 and 36: ACCESSING COMPONENT INSIDE THE DISH
Page 37 and 38: TROUBLESHOOTING GUIDE Model DU910PF
Page 39 and 40: Strip Circuits WASH (Steps 2 - 7, 1
Page 41 and 42: PROBLEM POSSIBLE CAUSES CORRECTION/
Page 43 and 44: STRIP CIRCUITS 39
Page 45 and 46: CYCLE TIMING CHART NOTES Note 1: Pr
Page 47 and 48: Section Three POWER CLEAN FILTER MO
Page 49 and 50: Servicing the Soil Sensing System T
Page 51 and 52: Fig. 3-12 Fig. 3-13 Fig. 3-14 47
Page 53 and 54: DIAGNOSTICS AND SALES DEMO TIMING C
Page 55 and 56: TECHNICAL INFORMATION Model DU940SC
Page 57 and 58: STRIP CIRCUITS CYCLE TIMING CHART 5
Page 59 and 60: Section Four INSTALLATION CONSIDERA
Page 61 and 62:
IMPORTANT Be sure the door panel is
Page 63 and 64:
INSTALLING THE FLOOR MOUNTING KIT K
show all

1998 Dishwashers Intro - Whirlpool

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?