1998 Dishwashers Intro - Whirlpool

More documents

Recommendations

Info

Replacing the Spring Loaded Locking Tab The inner door panel is held in place by a spring loaded locking tab located on the door frame rail, just below the console. (Fig. 2-14) To remove this assembly, remove the spring and slide the locking tab back until the locating tab is in the key hole. (Fig. 2-15) Then lift the locking tab up. To replace the assembly, reverse this procedure. Locking Tab Assembly Fig. 2-15 Fig. 2-14 32
TROUBLESHOOTING GUIDE Model DU910PFG PRECAUTIONS TO BE OBSERVED WHILE TROUBLESHOOTING AND DIAGNOSING PROBLEMS Always check wiring harness and connectors before initiating any test procedures. Disconnect electric power from the dishwasher before touching the printed circuit boards or re-seating wire connectors. Voltage checks should be made by inserting meter probes beside the wires in the connector blocks with the electric power source on and the connector block plugged in. Resistance checks should be made on components with the electric power off and the connector blocks disconnected. PROBLEM POSSIBLE CAUSES CORRECTION/TEST Dishwasher does not run or stops during a cycle 1. Door is not latching properly. 2. Child lock is "ON". 3. Wash Cycle not set properly. 4. Household fuse blown or circuit breaker tripped. 5. Washer is not wired into a circuit with proper voltage. 1. Check to make sure handle link is properly seated in door latch assembly. Check that the door switch is opening and closing properly. 2. Turn child lock "OFF" 3. Review setting Wash Cycles in the Use and Care Guide. 4. Have a qualified electrician check the circuit breaker or fuse. 5. Have customer call a qualified electrician. Dishwasher will not fill Dishwasher will not drain Dishwasher will not dry dishes 1. Overflow protection float is stuck in "up" position. 2. Fill valve is inoperable. 3. Open timer contacts. 1. Air gap (if installed) is clogged. 2. Pump motor is inoperable. 3. Open timer contacts. 1. Heater element burned out. 2. HI-limit thermostat inoperable. 3. Open circuit between timer and heater. 1. Check that the overflow protection float is free to move "up" and "down". Check that the overfill switch in opening and closing properly. 2. Check for continuity between contacts on fill valve. 3. Test timer contacts. 1. Follow air gap manufacturer's direction for cleaning. 2. Disconnect pump motor from wiring harness and check for continuity. 3. Test timer contacts. 1. Check for continuity between the terminals of the heater element. 2. Check for continuity between terminals of the hi-limit thermostat. 3. Check for continuity between timer switch contacts and heater. 33
Page 1 and 2: CONSUMER SERVICES TECHNICAL EDUCATI
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION. . .
Page 5 and 6: Section One DURAWASH MODELS WITH SO
Page 7 and 8: COMPONENT ACCESS ! WARNING ELECTRIC
Page 9 and 10: 4. Disconnect the drain hose from t
Page 11 and 12: Removing the Water Inlet Valve 1. T
Page 13 and 14: Removing the Timer 1. Disconnect th
Page 15 and 16: Fig. 1-28 Fig. 1-29 Fig. 1-30 Fig.
Page 17 and 18: SOLUTIONS TO COMMON PROBLEMS DIAGNO
Page 19 and 20: TROUBLESHOOTING GUIDE PRECAUTIONS T
Page 21 and 22: Cycle Timing Chart 17
Page 31 and 32: Section Two POWER CLEAN FILTER MODE
Page 33 and 34: Removing the Heater Element From be
Page 35: ACCESSING COMPONENT INSIDE THE DISH
Page 39 and 40: Strip Circuits WASH (Steps 2 - 7, 1
Page 41 and 42: PROBLEM POSSIBLE CAUSES CORRECTION/
Page 43 and 44: STRIP CIRCUITS 39
Page 45 and 46: CYCLE TIMING CHART NOTES Note 1: Pr
Page 47 and 48: Section Three POWER CLEAN FILTER MO
Page 49 and 50: Servicing the Soil Sensing System T
Page 51 and 52: Fig. 3-12 Fig. 3-13 Fig. 3-14 47
Page 53 and 54: DIAGNOSTICS AND SALES DEMO TIMING C
Page 55 and 56: TECHNICAL INFORMATION Model DU940SC
Page 57 and 58: STRIP CIRCUITS CYCLE TIMING CHART 5
Page 59 and 60: Section Four INSTALLATION CONSIDERA
Page 61 and 62: IMPORTANT Be sure the door panel is
Page 63 and 64: INSTALLING THE FLOOR MOUNTING KIT K

1998 Dishwashers Intro - Whirlpool

Create successful ePaper yourself

Delete template?

Save as template?