1998 Dishwashers Intro - Whirlpool

More documents

Recommendations

Info

2. Disconnect the wiring harness from the motor harness plug. 3. Rubber clamps secure the pump and motor assembly to the tub. Rotate these inward 90°. (Fig. 2-7) 4. Remove the drain hose and clamp from the check valve and unscrew the check valve from the pump. (Fig. 2-8) 5. Remove the tuned sound absorber. Use an open-end wrench to loosen the shaft from the motor. Do not loosen the sound absorber by torquing on the large tuned resonator. -- NOTE -- A small container will be required to catch water from the drain hose after removal. Check Valve Drain Hose Clamp Tuned Sound Absorber Drain Hose Clamp Shown Rotated Inward 90° Fig. 2-7 Fig. 2-8 6. Remove the pump and motor assembly by pulling up through the inside of the tub. (Fig. 2-9) Servicing the Operating Thermostat Fig. 2-9 The operating thermostat is secured to the bottom of the pump housing. (Fig. 2-10) 1. Disconnect the two (2) wiring harness leads from the terminals on the thermostat. 2. Remove the two (2) Hex-head screws securing the thermostat to the pump housing. Operating Thermostat Fig. 2-10 30
ACCESSING COMPONENT INSIDE THE DISHWASHER DOOR Removing Access and Outer Door Panels 1. Loosen but do not remove the two (2) toe panel screws below the access panel. Remove and set aside the two (2) screws above the access panel. (Fig. 2-11) 2. Remove the access panel assembly by sliding it upward to clear the loosened screws. (Fig. 2-11) 3. Remove the two (2) screws from the bottom of the outer door panel. (Fig. 2-11) 4. Pull the bottom of the outer door panel outward and slide it down approximately ¼” to ½”. The panel will then be free for removal. (Fig. 2-11, inset) 5. Remove the existing door insulation. Access to the detergent and rinse aid dispensers is now possible. Removing the Inside Door Panel 1. Disconnect the dishwasher from the electrical supply. 2. Disconnect the end of the door springs from the door spring tension adjustment holes in the frame runner. Fig. 2-11 T-15 TORX 3. Open the dishwasher door and remove the eight (8) T-15 Torx screws securing the inner door panel from the door frame. (Fig. 2-12) 4. Slide the inner door panel back toward the dishwasher to disengage the spring loaded locking tab from the door panel, then lift the door panel away from the door. (Fig. 2-13) 4. Remove the control cover. Fig. 2-13 Inner Door Panel SLIDE INNER DOOR PANEL TOWARD DISHWASHER Fig. 2-12 Spring Loaded Locking Tab 31
Page 1 and 2: CONSUMER SERVICES TECHNICAL EDUCATI
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION. . .
Page 5 and 6: Section One DURAWASH MODELS WITH SO
Page 7 and 8: COMPONENT ACCESS ! WARNING ELECTRIC
Page 9 and 10: 4. Disconnect the drain hose from t
Page 11 and 12: Removing the Water Inlet Valve 1. T
Page 13 and 14: Removing the Timer 1. Disconnect th
Page 15 and 16: Fig. 1-28 Fig. 1-29 Fig. 1-30 Fig.
Page 17 and 18: SOLUTIONS TO COMMON PROBLEMS DIAGNO
Page 19 and 20: TROUBLESHOOTING GUIDE PRECAUTIONS T
Page 21 and 22: Cycle Timing Chart 17
Page 31 and 32: Section Two POWER CLEAN FILTER MODE
Page 33: Removing the Heater Element From be
Page 37 and 38: TROUBLESHOOTING GUIDE Model DU910PF
Page 39 and 40: Strip Circuits WASH (Steps 2 - 7, 1
Page 41 and 42: PROBLEM POSSIBLE CAUSES CORRECTION/
Page 43 and 44: STRIP CIRCUITS 39
Page 45 and 46: CYCLE TIMING CHART NOTES Note 1: Pr
Page 47 and 48: Section Three POWER CLEAN FILTER MO
Page 49 and 50: Servicing the Soil Sensing System T
Page 51 and 52: Fig. 3-12 Fig. 3-13 Fig. 3-14 47
Page 53 and 54: DIAGNOSTICS AND SALES DEMO TIMING C
Page 55 and 56: TECHNICAL INFORMATION Model DU940SC
Page 57 and 58: STRIP CIRCUITS CYCLE TIMING CHART 5
Page 59 and 60: Section Four INSTALLATION CONSIDERA
Page 61 and 62: IMPORTANT Be sure the door panel is
Page 63 and 64: INSTALLING THE FLOOR MOUNTING KIT K

1998 Dishwashers Intro - Whirlpool

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?