1998 Dishwashers Intro - Whirlpool

More documents

Recommendations

Info

COMPONENT ACCESS INDICATOR LIGHTS TIMER PROGRAM SWITCHES DETERGENT AND RINSE AID DISPENSER ASSEMBLY LATCH ASSEMBLY HEATER FILL VALVE MOTOR RELAY PUMP AND MOTOR ASSEMBLY FLOAT SWITCH OPERATING THERMOSTAT (Attached to bottom of pump housing) HI LIMIT THERMOSTAT 28
Removing the Heater Element From beneath the cabinet: 1. Remove the front access panel. (See Removing the Outer Door Panel) 2. Pull the spade connectors off the heater element terminals. 3. Unscrew the two (2) nuts securing the heater element to the bottom of the tub. (Fig. 2-5) From inside the tub: 4. Remove the lower dish rack. 5. Remove the lower spray arm. Fig. 2-5 6. Slide the metal disks from the metal clips securing the left and right sides of the heater element. . 7. Carefully lift the heater element from the unit. Replacing the Heater Element Element Retaining Nuts (2) From inside the tub: 1. Carefully place the terminal ends of the heater element through the two (2) holes at the bottom rear of the cabinet. 2. Slide the metal disks into the clips to secure the left and right sides of the heater element. 3. Replace the lower spray arm. 4. Replace the lower dish rack. From underneath the cabinet: 5. Secure the heater element in place with two (2) nuts. Be sure the element is seated firmly against the tub. 6. Slide the spade connectors onto the heater element terminals. 7. Replace the front access panel. Removing the Pump Motor Assembly 1. Unscrew and remove the nozzle cap and remove the nozzle bearing and spray arm. (Fig. 2-6) SPRAY ARM NOZZLE CAP NOZZLE BEARING Fig. 2-6 29
Page 1 and 2: CONSUMER SERVICES TECHNICAL EDUCATI
Page 3 and 4: TABLE OF CONTENTS INTRODUCTION. . .
Page 5 and 6: Section One DURAWASH MODELS WITH SO
Page 7 and 8: COMPONENT ACCESS ! WARNING ELECTRIC
Page 9 and 10: 4. Disconnect the drain hose from t
Page 11 and 12: Removing the Water Inlet Valve 1. T
Page 13 and 14: Removing the Timer 1. Disconnect th
Page 15 and 16: Fig. 1-28 Fig. 1-29 Fig. 1-30 Fig.
Page 17 and 18: SOLUTIONS TO COMMON PROBLEMS DIAGNO
Page 19 and 20: TROUBLESHOOTING GUIDE PRECAUTIONS T
Page 21 and 22: Cycle Timing Chart 17
Page 31: Section Two POWER CLEAN FILTER MODE
Page 35 and 36: ACCESSING COMPONENT INSIDE THE DISH
Page 37 and 38: TROUBLESHOOTING GUIDE Model DU910PF
Page 39 and 40: Strip Circuits WASH (Steps 2 - 7, 1
Page 41 and 42: PROBLEM POSSIBLE CAUSES CORRECTION/
Page 43 and 44: STRIP CIRCUITS 39
Page 45 and 46: CYCLE TIMING CHART NOTES Note 1: Pr
Page 47 and 48: Section Three POWER CLEAN FILTER MO
Page 49 and 50: Servicing the Soil Sensing System T
Page 51 and 52: Fig. 3-12 Fig. 3-13 Fig. 3-14 47
Page 53 and 54: DIAGNOSTICS AND SALES DEMO TIMING C
Page 55 and 56: TECHNICAL INFORMATION Model DU940SC
Page 57 and 58: STRIP CIRCUITS CYCLE TIMING CHART 5
Page 59 and 60: Section Four INSTALLATION CONSIDERA
Page 61 and 62: IMPORTANT Be sure the door panel is
Page 63 and 64: INSTALLING THE FLOOR MOUNTING KIT K

1998 Dishwashers Intro - Whirlpool

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?