Steam Generator Installation Manual - Clayton Industries

More documents

Recommendations

Info

Steam Generator & Fluid Heater Installation Manual NOTE 1: Barometric dampers are recommended on all installations with stack heights over 20 feet (6 meters) and on any low NOx units. NOTE 2: A removable, 4 feet (1.2 meters) minimum, stack section is recommended to facilitate steam generator/fluid heater maintenance and repair. NOTE 3: A backdraft damper must be installed in the exhaust stack for installations in cold weather climates. All backdraft dampers must be air-tight and proof-of-position switches. NOTE 4: Oil-fired units require a 2W x 3H feet (0.6W x 0.9H meter) access portal in the stack for inspection and water washing. A floor drain is required at the bottom of the generator under or close to the burner opening. Figure 2-2 Standard exhaust stack layout for natural gas and light-oil installations only. Not recommended for heavy-oil machines. Sect02_Genrl-xx4_s.fm 2-8 04/21/2015
Section II - General Information *See Notes 1 – 4 in Figure 2-2. Figure 2-3 Alternate multi-unit exhaust stack layout for natural gas and light-oil installations only. Not recommended for heavy-oil units. 04/21/2015 2-9 Sect02_Genrl-xx4_s.fm
Page 1 and 2: Cover E-Series Steam Generator & Fl
Page 3 and 4: Title Page Steam Generator and Flui
Page 5 and 6: Table of Contents Section 1 Introdu
Page 7 and 8: 6.5 Safety Controls ...............
Page 9 and 10: SECTION I - INTRODUCTION The CLAYTO
Page 11 and 12: SECTION II - GENERAL INFORMATION 2.
Page 13 and 14: Section II - General Information It
Page 15 and 16: Section II - General Information 2.
Page 17: Section II - General Information Ex
Page 25 and 26: Section II - General Information NO
Page 27 and 28: Section II - General Information BH
Page 29 and 30: Section II - General Information Fi
Page 31 and 32: Section II - General Information Th
Page 37 and 38: Section II - General Information g
Page 39 and 40: Section II - General Information A
Page 41 and 42: SECTION III - CLAYTON FEEDWATER PUM
Page 43 and 44: Section III Water supply piping to
Page 45 and 46: Section III Drain Condensate Return
Page 47 and 48: Section III Gravity Fill Vent Chemi
Page 49 and 50: SECTION IV - FUEL SYSTEM 4.1 GENERA
Page 51 and 52: Section IV The Clayton light oil bu
Page 53 and 54: SECTION V - TRAP SEPARATORS 5.1 GEN
Page 55 and 56: Section V R20202A Figure 5-1 Trap s
Page 57 and 58: Section V R20202A Figure 5-3 Trap s
Page 59 and 60: SECTION VI - TECHNICAL SPECIFICATIO
Page 61 and 62: Section VI - Technical Specificatio
Page 69 and 70:
Section VI - Technical Specificatio
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
SECTION VII - OPTIONAL EQUIPMENT 7.
Page 83 and 84:
Section VII 7.5.2 Pressure Regulati
Page 85 and 86:
SUPPLEMENT I - SCR 1.1 SEMI-CLOSED
Page 87 and 88:
Supplement I 1.1.11 Make-up Tank A
Page 89 and 90:
SUPPLEMENT II - HEAVY OIL 2.1 HEAVY
Page 91 and 92:
Supplement II NOTE All heavy oil fi
Page 93 and 94:
2.2 FUELS The conversion chart belo
Page 95 and 96:
ASTM Distillation Range Initial Boi
Page 97 and 98:
SUPPLEMENT III - FLUID HEATER 3.1 F
Page 99 and 100:
Appendix A - Steam Generator Liftin
Page 101 and 102:
Appendix A *Safety cable must be us
Page 103 and 104:
Appendix B - Saturated Steam P-T Ta
Page 105 and 106:
Appendix C - Piping and Instrumenta
Page 107 and 108:
04/22/2015 C-9 P&ID_a.fm
Page 109 and 110:
04/22/2015 C-11 P&ID_a.fm
Page 111 and 112:
04/22/2015 C-13 P&ID_a.fm
Page 113 and 114:
04/22/2015 C-15 P&ID_a.fm
Page 115 and 116:
04/22/2015 C-17 P&ID_a.fm
Page 117 and 118:
04/22/2015 C-19 P&ID_a.fm
Page 119 and 120:
Appendix D - Installing SE Option A
Page 121 and 122:
Appendix D INTRODUCTION A Clayton S
Page 123 and 124:
Appendix D d. Secure the top coil a
Page 125 and 126:
Appendix D FEEDWATER DISCHARGE-SE C
Page 128:
Back Cover 17477 Hurley Street, Cit
show all

Steam Generator Installation Manual - Clayton Industries

Create successful ePaper yourself

Delete template?

Save as template?