2013 AGCO Application Parts & Accessories Catalog - AGCO Parts
2013 AGCO Application Parts & Accessories Catalog - AGCO Parts
2013 AGCO Application Parts & Accessories Catalog - AGCO Parts
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
TeeJet GPS Speed Sensor<br />
• The GPS Speed Sensor uses a GPS<br />
receiver to measure true ground speed, then<br />
delivers a frequency signal compatible with<br />
the radar speed signal input on most controls<br />
and monitors<br />
• Eliminates problems frequently found with<br />
radar speed sensors on wet surfaces, with<br />
moving crops, or vehicle vibration<br />
• Convenient enclosure mounts inside cab,<br />
only a small patch antenna is mounted outside<br />
• Status LEDs show power, GPS lock and speed output conditions<br />
• Adapter cables make it compatible with Raven application rate control<br />
systems<br />
• State of the art GPS engine delivers better performance than many<br />
comparable units on the market<br />
• Speed range of 0.5-80+ mph (1-130+ km/h)<br />
• Quick signal acquisition (less than 1 second)<br />
Note: Kit includes GPS Speed Sensor, Patch Antenna, and Raven<br />
adapter cable.<br />
| Part | Description |<br />
| AG427257 | Kit, GPS Speed Sensor for Raven Controls |<br />
| AG427259 | GPS Speed Sensor with 3 position Conxall connector |<br />
| AG427258 | Patch Antenna |<br />
CAN SmarTrax TM 3D<br />
The CAN SmarTrax provides a more integrated<br />
and seamless installation. The yaw<br />
sensor has been integrated into the control<br />
node and all programming and operation can<br />
now be performed via the Viper Pro,<br />
Envizio Pro (II), or Cruizer II. The 3D<br />
upgrade provides compensation for roll, pitch and yaw to improve performance<br />
in rough and uneven terrain.<br />
When combined with a Phoenix 300 receiver utilizing OmniStar HP correction,<br />
2”-4” swath accuracy can be achieved up to 10 mph with 3D<br />
activated. CAN SmarTrax kits consist of three or four components:<br />
• CAN SmarTrax node kit<br />
• Machine-specific hydraulic installation kit<br />
• Viper Pro, Envizio Pro (II), or Cruizer II<br />
• DGPS receiver (Not required with Envizio Pro (II) w/ GPS or<br />
Cruizer II)<br />
CAN SmarTrax TM 3D<br />
These node kits are for use with traditional style cable (round 10-pin<br />
connector).<br />
These kits will only work with hydraulic steer kits using this format: 117-<br />
0295-xxx<br />
All kits other than those for the original Cruizer will require an AG727393<br />
CAN power tee and terminator kit if no CAN system is already present.<br />
| Part | Description |<br />
| AG427706 | Controller Kit, CAN SmarTrax w/ 3D for Viper |<br />
| | Pro/Envizio Pro |<br />
| AG427708 | Controller Kit, CAN SmarTrax w/ 3D for Cruizer |<br />
| AG428364 | Controller Kit, CAN SmarTrax w/3D for Cruizer II |<br />
| AG428363 | Controller Kit, CAN SmarTrax w/3D for WR Cruizer II |<br />
| AG427765 | Install Kit, RoGator 854 (1996 and older)/664 |<br />
| AG427766 | Install Kit, RoGator 854 (1997 model) |<br />
| AG427767 | Install Kit, RoGator 854 (1998 and newer) |<br />
| AG427771 | Install Kit, TerraGator 1903 |<br />
| AG427830 | Install Kit, SpraCoupe 220 |<br />
| AG427828 | Install Kit, SpraCoupe 3000/4000 |<br />
| AG427772 | Install Kit, <strong>AGCO</strong> DT 160/180/200/225/240 |<br />
| AG427773 | Install Kit, <strong>AGCO</strong> Allis 9635/9655/9675/9695 |<br />
CAN SmarTrax TM 3D<br />
These kits are for the new series of valves.<br />
These kits will only work with hydraulic steer kits using this format:<br />
117-4001-xxx<br />
All kits other than those for the original Cruizer will require an<br />
AG727393 CAN power tee and terminator kit if no CAN system is<br />
already present.<br />
| Part | Description |<br />
| AG428306 | Controller Kit, CAN SmarTrax w/3D for Viper |<br />
| | Pro/Envizio Pro |<br />
| AG428308 | Controller Kit, CAN SmarTrax w/3D for Cruizer |<br />
| AG428367 | Controller Kit, CAN SmarTrax w/3D for WR Cruizer II |<br />
| AG428368 | Controller Kit, CAN SmarTrax w/3D for Cruizer II |<br />
| AG428318 | Install Kit, RoGator 1254 |<br />
| AG428322 | Install Kit, RoGator 64/74 Series (Excluding 664), |<br />
| | SS (JIC Fittings) |<br />
| AG428328 | Install Kit, RoGator 84/86/94/96 Series |<br />
| | (Flat Face O-Ring Fittings) |<br />
| AG428321 | Install Kit, TerraGator 1603/1803/1804 |<br />
| AG428317 | Install Kit, TerraGator |<br />
| | 6103/6203/8103/8104/8144/8203/8204/8244/9103/9203 |<br />
| AG427711 | Install Kit, TerraGator 6203/82XX/83XX (2009 and newer) |<br />
| AG428325 | Install Kit, SpraCoupe 7X5X, 7X60 |<br />
CAN SmarTrax 3D - Challenger Steer-Ready Kits<br />
| Part | Description |<br />
| AG428378 | Install Kit with 3D - MT700, MT800 C-Series with |<br />
| | Viper Pro/Envizio Pro (Requires 2 cables below) |<br />
| AG428379 | VPro/EPro, Cable Power/CAN |<br />
| AG428380 | VPro/EPro, Cable Cab |<br />
| AG428378 | Install Kit with 3D - MT700, MT800 C-Series |<br />
| | with Cruizer 2 (Requires console cable below) |<br />
| AG428381 | Cable Console Cruizer 2 |<br />
| AG428304 | Install Kit with 3D - MT700, MT800 C-Series with |<br />
| | original Cruizer (Includes cable) |<br />
| AG428305 | Install Kit w/out 3D - MT700, MT800 C-Series with |<br />
| | original Cruizer (Includes cable) |<br />
CAN SmarTrax TM 3D Upgrades<br />
NEW!<br />
| Part | Description |<br />
| AG428300 | Kit, SmarTrax node upgrade, Viper Pro/Envizio Pr o |<br />
| AG428301 | Kit, SmarTrax 3D node upgrade, Viper Pro/Envizio Pro |<br />
| AG427709 | Authorization Code, SmarTrax 3D |<br />
Precision Products<br />
29