Light Duty Technology Cost Analysis, Power - US Environmental ...

More documents

Recommendations

Info

Figure D-75: NiMH Battery Sub-Modules Contain Eight (8) D-Cells Assemble in Series The D-Cell construction at the most basic level consists of a stamped can, into which an anode collector and rolled electrode assembly are inserted. A cathode collector and vented top are then fitted to the can with a seal. The can is finished with a rolled metal edge which seals and secures the top to the can. Figure D-76 shows some of the basic components used to produce a D-cell battery. Figure D-76: NiMH Cell Construction 110
Circuit connections between packs are small buss bars in a molded carrier for insulation (Figure D-77). Voltage sensors are integrated into the connection assembly. Temperature sensors are placed strategically at five (5) places in the traction battery assembly. Figure D-77: Battery Connections and Sensors Stamped steel covers (Figure D-78 and Figure D-79) are employed to closeout and direct air flow over the batteries. A cooling plenum (Figure D-80) and speed regulated fan (Figure D-81) are mounted to the rear of the traction battery assembly. The fan pulls air through the battery housing from under the rear seat bottom in the cabin. Figure D-78: Stamped Battery Cover (Under plenum, luggage compartment side) 111
Page 1 and 2:
Light Duty Technology Cost Analysis
Page 3 and 4:
Contents A. EXECUTIVE SUMMARY......
Page 5 and 6:
Figures FIGURE A-1: POWER-SPLIT SYS
Page 7 and 8:
FIGURE D-90: HIGH VOLTAGE HARNESS C
Page 9 and 10:
A. Executive Summary Light-Duty Tec
Page 11 and 12:
Internal Combustion Engine (ICE) Ot
Page 13 and 14:
Table A-1: Net Incremental, Direct
Page 15 and 16:
Table A-2: P2 Vehicle Segment Mass
Page 17 and 18:
Table A-4 and Table A-5 provide add
Page 19 and 20:
B. Introduction B.1 Objectives The
Page 21 and 22:
B.2 Process Flow and Key Supporting
Page 23 and 24:
Step 6: Phase 2 (component/assembly
Page 25 and 26:
Table B-1: Summary of Universal Cos
Page 27 and 28:
C. Costing Methodology C.1 Teardown
Page 29 and 30:
An example of a custom complex mode
Page 31 and 32:
For a component which has a serial
Page 33 and 34:
C.2 Cost Model Overview The cost pa
Page 35 and 36:
Lastly, the “Net Incremental Dire
Page 37 and 38:
considered. For example, forged com
Page 39 and 40:
part, while “buy” indicates an
Page 41 and 42:
C.4.3.3 Contributors to Labor Rate
Page 43 and 44:
sided part, CNC turning, auto bar f
Page 45 and 46:
The Primary Process Equipment secti
Page 47 and 48:
For this cost analysis study, four
Page 49 and 50:
very difficult to predict and are v
Page 51 and 52:
C.4.6.2 Types of Packaging and Sele
Page 53 and 54:
capture additional quote details an
Page 55 and 56:
Project Process Requirement Minimum
Page 57 and 58:
information from both technology co
Page 59 and 60:
and transit lead times. This equate
Page 61 and 62:
study. These vehicles provided a ve
Page 63 and 64:
Table D-1: Vehicle Specification Su
Page 65 and 66:
D.1.2 Direct Manufacturing Cost Dif
Page 67 and 68: D.2 Engine System and Cost Summary
Page 69 and 70: D.3 Transmission System and Cost Su
Page 71 and 72: D.3.1.2 Gear Train Subsystem The po
Page 73 and 74: The generator stator (Figure D-10)
Page 75 and 76: The traction motor stator (Figure D
Page 77 and 78: The generator control unit (Figure
Page 79 and 80: The CVT control circuit board (Figu
Page 81 and 82: The speed sensor for the traction m
Page 83 and 84: D.3.1.4 Transmission Cooling System
Page 85 and 86: The electric pump (Figure D-30 ) is
Page 87 and 88: technology adaptation (i.e., driven
Page 89 and 90: Item Table D-5: Net Incremental Dir
Page 91 and 92: Item Table D-6: eCVT Motor and Cont
Page 93 and 94: Figure D-34: HEV Fusion, Under Engi
Page 95 and 96: ase to the body. The seat cover is
Page 97 and 98: Figure D-43: Expanded Polypropylene
Page 99 and 100: D.4.2 Body System Cost Impact As sh
Page 101 and 102: Figure D-49: Key Components of Brak
Page 103 and 104: D.5.1.2 Power Brake Subsystem D.5.1
Page 105 and 106: Figure D-56: Actuator Solenoid and
Page 107 and 108: Table D-8: Net Incremental Direct M
Page 109 and 110: D.6.1.2 Refrigeration/Air Condition
Page 111 and 112: The two (2) main housings and both
Page 113 and 114: Figure D-67: Main Housing and Elect
Page 115 and 116: The rotor shaft is mounted to an in
Page 117: D.7 Electrical Power Supply System
Page 121 and 122: The traction battery assembly is mo
Page 123 and 124: During dormant periods the BEC (Fig
Page 125 and 126: D.7.2 Electrical Power Supply Cost
Page 127 and 128: Item 1 2 3 4 5 6 7 8 9 10 11 12 13
Page 129 and 130: The HV connectors (Figure D-91) are
Page 131 and 132: Item Table D-12: Net Incremental Di
Page 133 and 134: F. Power-Split Scaling Cost Analysi
Page 135 and 136: vehicle class was determined. Also
Page 137 and 138: G. 2010 Hyundai Avante Lithium Poly
Page 139 and 140: Figure G-3: Li Ion Battery Modules
Page 141 and 142: Figure G-6: Cell Covers in Module,
Page 143 and 144: Figure G-9: The Battery Pack Discon
Page 145 and 146: Table G-2: 2010 Hyundai Avante Lith
Page 147 and 148: Table H-1: Baseline Powertrain and
Page 149 and 150: Table H-2: Primary Component Sizing
Page 151 and 152: Costing Databases: the five (5) cor
Page 153: Surrogate part: a part similar in f
show all

Light Duty Technology Cost Analysis, Power - US Environmental ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?