IQ plusÂ® 800/810 - Rice Lake Weighing Systems

More documents

Recommendations

Info

2.0 Installation2.1 Power ConnectionsThe IQ plus 800/810 can operate from either a 115VAC or 230 VAC 3-wire power supply line at 50 or 60Hz. It is further recommended that the 800/810 beconnected to an AC power supply that is on a separatebranch or feeder from other AC equipment that causesstep-load changes and/or other AC line disturbances.The transformer on the power supply/display board ispre-wired at the factory for 115 VAC operation. If theinstallation requires 230 VAC operation, move thetransformer connector from J5 to J9 on the powersupply/display board. Also, be sure to install thecorrect fuse. See Section 10.7 on page 91 forspecifications2.2 Board ConnectionsThe main CPU board is connected to the powersupply/display board by two ribbon cables. The powerribbon cable connects between J1 on both boards; thedata ribbon cable connects between J2 on both boards.Figures 2-1 through 2-3 show board locations andcabling for the IQ plus 810, HE, and SS models.Board locations and cabling for the IQ plus 800 areessentially the same as for the IQ plus 810.SERIAL COMM WIRINGJ7-1J7-2 PINS 1–6:J7-3 PRINTER PORTJ7-4 CONNECTORSJ7-5J7-6J7-7J7-8 PINS 7–12:J7-9 EDP PORTJ7-10 CONNECTORSJ7-11J7-12MAINBOARDDISPLAYBOARDTO J10SETUPSWITCHLOAD CELLTO J7J7SERIALCOMMUNICATIONSGROUNDSERIAL COMMUNICATIONSCABLE TO J7GROUNDTO J4J4DIGITAL I/OLOAD CELLCABLE TO J10DIGITAL I/OCABLE TO J4AC POWERAC POWERJ10SETUP SWITCHJ7DIGITAL I/O WIRINGJ4-1 DIG OUT 1J4-2 DIG OUT 2J4-3 DIG OUT 3J4-4 DIG OUT 4J4-5 DIG IN 3J4-6 DIG IN 2J4-7 DIG IN 1J4-8 GNDJ4-9 GNDJ4-10 +5 VDCFigure 2-1. IQ plus 810 Wiring, Side ViewJ10-1 +SigJ10-2 –SigJ10-3 +SenseJ10-4 –SenseJ10-5 ShieldJ10-6 +ExcJ10-7 –Exc7 6 5 4 3 2 1Load Cell WiringJ10Figure 2-2. IQ plus 810 Wiring, Top View6 IQ plus 800/810 Installation Manual
REMOVE JUMPERJ11 BEFOREINSTALLINGBATTERYREMOVE JUMPERJ11 BEFOREINSTALLINGBATTERYPower Supply Display BoardDisplay DriverBatteryJ2PowerRibbonCableDIGITAL I/O WIRINGJ4-10 +5 VDCJ4-9 GNDJ4-8 GNDJ4-7 DIG IN 1J4-6 DIG IN 2J4-5 DIG IN 3J4-4 DIG OUT 4J4-3 DIG OUT 3J4-2 DIG OUT 2J4-1 DIG OUT 1J1J6FuseDataCableCPU BoardA/D ModuleJ2J1DataRibbonCableSetup SwitchTransformerAC Power CablePower Ribbon CableSERIAL COMM.J7-12J7-11J7-10 7-12J7-9 EDPJ7-8 PORTJ7-7J7-6J7-5 1-6J7-4 PRINTERJ7-3 PORTJ7-2J7-11 2 3 4 5 6 7LOAD CELL WIRING1 +Sig2 –Sig3 +Sense4 –Sense5 Shield6 +Exc7 –ExcAC Power InFigure 2-3. IQ plus 810 SS WiringAC PowerCablePower Supply Display BoardFuseDisplayDriverJ6BatteryJ2DataRibbonCableTransformerJ4DIGITAL I/O WIRINGJ4-10 +5 VDCJ4-9 GNDJ4-8 GNDJ4-7 DIG IN 1J4-6 DIG IN 2J4-5 DIG IN 3J4-4 DIG OUT 4J4-3 DIG OUT 3J4-2 DIG OUT 2J4-1 DIG OUT 1J1CPU BoardA/D ModuleJ2J1Power RibbonCablePowerRibbonCableJ7J4KeyboardAC PowerCablePre-drilled holes forBatching Switch OptionSERIAL COMM.J7-12J7-11J7-10J7-9J7-8J7-7J7-6J7-5J7-4J7-3J7-2J7-1Setup Switch7-12EDPPORT1 2 3 4 5 6 71-6PRINTERLOAD CELL WIRINGPORT 1 +Sig234567 –Sig+Sense–SenseShield+Exc–ExcAC Power InFigure 2-4. IQ plus 810 HE WiringInstallation 7
Page 1: IQ plus ® 800/810Digital Weight In
Page 4 and 5: 5.3 Truck Modes ...................
Page 6 and 7: ivIQ plus 800/810 Installation Manu
Page 8 and 9: 1 23 4 5 6 7 8 910 11 12 13 14 15 1
Page 10 and 11: DISPTARETIME/DATEDISPACCUMDISPROCNE
Page 14 and 15: 2.3 Board DiagramsFigures 2-5 throu
Page 16 and 17: 2.7 Wall- and Panel-MountingThe fol
Page 18 and 19: LbKgROCA cumDISPTARETIME/DATEZERODI
Page 20 and 21: Revolution provides online help for
Page 22 and 23: CONFIG MenuParameter Choices Descri
Page 24 and 25: CONFIG MenuParameter Choices Descri
Page 26 and 27: 3.2.3 Format MenuCONFIGXXXXXXX SET
Page 28 and 29: FORMAT MenuUNITSSecondary UnitsDSP
Page 30 and 31: Batch setpointsAPAUSE DELAY WAIT SS
Page 32 and 33: SETPNTS MenuParameter Choices Descr
Page 34 and 35: SETPNTS MenuParameter Choices Descr
Page 36 and 37: 3.2.5 Serial MenuSee Section 10.3 o
Page 38 and 39: SERIAL MenuParameter Choices Descri
Page 40 and 41: 3.2.7 Digital Input MenuCONFIGXXXXX
Page 42 and 43: 3.2.9 Bar Graph MenuSee Section 9.7
Page 44 and 45: 4.0 CalibrationBefore beginning wei
Page 46 and 47: 4.2 EDP Command CalibrationTo calib
Page 48 and 49: Value swapping ensures that the low
Page 50 and 51: Suppose the user has the following
Page 52 and 53: 6.1.2 Reporting CommandsReporting c
Page 54 and 55: Command Description ValuesBATCHNG B
Page 56 and 57: Command Description ValuesWZERO#x Z
Page 58 and 59: Translating ASCII Status Data ASCII
Page 60 and 61: 7.0 Print FormattingThe IQ plus 800
Page 62 and 63:
Figure 7-2 shows an example of the
Page 64 and 65:
7.3 Extended Print Format CommandsY
Page 66 and 67:
INRANGE-GROSS-NETKindBATCHPRTIMERCO
Page 68 and 69:
Batch Status MessagesTable 8-3 show
Page 70 and 71:
9.0 Optional and Advanced Features9
Page 72 and 73:
9.3 Peak Hold FunctionThe peak hold
Page 74 and 75:
9.6 Batching SwitchThe batching swi
Page 76 and 77:
Figure 9-6 shows the BAR GRF menu u
Page 78 and 79:
MAIN CPU BOARDEXPANSION BOARDTable
Page 80 and 81:
1R5CH-2J10CCH-1J10BJ10ASETUP SWITCH
Page 82 and 83:
9.12 Multiple Scale InputsThe stand
Page 84 and 85:
9.14 Setpoint Digital Output Expand
Page 86 and 87:
AC WIRING TO CONTROLLED EQUIPMENT I
Page 88 and 89:
9.16 Jetpak High Speed OptionThe Je
Page 90 and 91:
10.0 Appendix10.1 Error MessagesIf
Page 92 and 93:
ASCII Dec Hex ASCII Dec Hex ASCII D
Page 94 and 95:
10.4 Conversion Factors for Seconda
Page 96 and 97:
10.6 Software Revision HistoryVersi
Page 98 and 99:
O NEnclosure Classification:800 NEM
show all

IQ plusÂ® 800/810 - Rice Lake Weighing Systems

Create successful ePaper yourself

Delete template?

Save as template?