vacon 100 installation manual - VEM motors Finland Oy

More documents

Recommendations

Info

Power cabling vacon • 244. POWER CABLINGThe mains cables are connected to terminals L1, L2 and L3 and the motor cables to terminalsmarked with U, V and W. See principal connection diagram in Figure 17. See also Table 14 forthe cable recommmendations for different EMC levels.KeypadControlL1L2L3Power unitU/T1V/T2W/T3MFigure 17. Principal connection diagramUse cables with heat resistance of at least +70°C. The cables and the fuses must be dimensionedaccording to the AC drive nominal OUTPUT current which you can find on the ratingplate.EMC levelsCable type 1st environment 2nd environmentCategory C2 Category C3 Level C4Mains cable 1 1 1Motor cable 3* 2 2Control cable 4 4 4Table 14. Cable types required to meet standards1 = Power cable intended for fixed installation and the specific mains voltage. Shieldedcable not required. (MCMK or similar recommended).2 = Symmetrical power cable equipped with concentric protection wire and intended for thespecific mains voltage. (MCMK or similar recommended). See Figure 18.24-hour support +358 (0)201 212 575 • Email: vacon@vacon.com4
vacon • 25Power cabling3 = Symmetrical power cable equipped with compact low-impedance shield and intendedfor the specific mains voltage. [MCCMK, EMCMK or similar recommended; Recommendedcable transfer impedance (1...30MHz) max. 100mohm/m]. See Figure 18.*360º earthing of the shield with cable glands in motor end needed for EMC level C2.4 = Screened cable equipped with compact low-impedance shield (JAMAK, SAB/ÖZCuY-Oor similar).PE conductorand shieldPE conductorsShieldFigure 18.NOTE: The EMC requirements are fulfilled at factory defaults of switching frequencies (allframes).NOTE: If safety switch is connected the EMC protection shall be continuous over the whole cableinstallation.4Tel. +358 (0) 201 2121 • Fax +358 (0)201 212 205
Page 1 and 2: vacon 100ac drivesinstallation manu
Page 3 and 4: vacon • 16.3.3 Frame MR9.........
Page 5 and 6: vacon • 3EC DECLARATION OF CONFOR
Page 7 and 8: vacon • 5Safety1.2 WarningsVacon
Page 9 and 10: vacon • 7SafetyDo not perform any
Page 11 and 12: vacon • 9Receipt of delivery2.1 T
Page 13 and 14: vacon • 11Receipt of delivery2.3
Page 15: vacon • 13Receipt of delivery2.3.
Page 19: vacon • 17MountingFigure 9. Vacon
Page 22 and 23: Mounting vacon • 203.1.2.2 Flange
Page 24 and 25: Mounting vacon • 22Note that if s
Page 28 and 29: Power cabling vacon • 264.1 UL st
Page 30 and 31: Power cabling vacon • 284.1.1.2 C
Page 32 and 33: Power cabling vacon • 304.1.1.4 C
Page 34 and 35: Power cabling vacon • 32Frame A1
Page 36 and 37: Power cabling vacon • 345• Inse
Page 38 and 39: Power cabling vacon • 367Connect
Page 40 and 41: Power cabling vacon • 384.3.2 Fra
Page 42 and 43: Power cabling vacon • 40M4 x 81 2
Page 44 and 45: Power cabling vacon • 427Cut the
Page 46 and 47: Power cabling vacon • 44Connector
Page 48 and 49: Power cabling vacon • 46M4x10Figu
Page 50 and 51: Control unit vacon • 485. CONTROL
Page 52 and 53: Control unit vacon • 505.1.2 Cont
Page 54 and 55: Control unit vacon • 525.1.2.1 Se
Page 56 and 57: Control unit vacon • 54max. 40 mm
Page 58 and 59: Control unit vacon • 56Strip abou
Page 60 and 61: Control unit vacon • 58Unless alr
Page 62 and 63: Control unit vacon • 605.4 Galvan
Page 64 and 65: Commissioning vacon • 626. COMMIS
Page 66 and 67: Commissioning vacon • 646.2.1 Cab
Page 68 and 69: Commissioning vacon • 666.3.2 Fra
Page 70 and 71: Commissioning vacon • 682Further
Page 72 and 73: Commissioning vacon • 7024-hour s
Page 74 and 75: Technical data vacon • 727.1.2 Ma
Page 76 and 77:
Technical data vacon • 747.2 Vaco
Page 78 and 79:
Technical data vacon • 767.2.1 Te
Page 80:
Find your nearest Vacon officeon th
show all

vacon 100 installation manual - VEM motors Finland Oy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?