vacon 100 installation manual - VEM motors Finland Oy

More documents

Recommendations

Info

Power cabling vacon • 304.1.1.4 Cable and fuse sizes, frames MR7 to MR9, North AmericaThe recommended fuse types are gG/gL (IEC 60269-1) or class T (UL & CSA). The fuse voltagerating should be selected according to the supply network. The final selection should be madeaccording to local regulations, cable installation conditions and cable specification. Bigger fusesthan what is recommended below shall not be used.Check that the fuse operating time is less than 0.4 seconds. Operating time depends on usedfuse type and impedance of the supply circuit. Consult the factory about faster fuses. Vacon offersrecommendations also for high speed J (UL & CSA ), aR (UL recognized, IEC 60269-4) andgS (IEC 60269-4) fuse ranges.FrameMR7MR8MR9Type0075 20072 40088 20087 40105 20105 40140 20140 40170 20170 40205 20205 40261 20261 40310 20310 475,072,088,087,0I L[A]Fuse(class T)[A]Mains, motorand groundcableCuTerminal cable sizeMain terminalEarth terminal100 AWG2 AWG9-AWG2/0 AWG9-AWG2/0110 AWG1 AWG9-AWG2/0 AWG9-AWG2/0105,0 150 AWG1/0 AWG9-AWG2/0 AWG9-AWG2/0140,0 200 AWG3/0 AWG1-350 kcmil AWG1-350 kcmil170,0 225 250 kcmil AWG1-350 kcmil AWG1-350 kcmil205,0 250 350 kcmil AWG1-350 kcmil AWG1-350 kcmil261,0 350 2*250 kcmil AWG1-350 kcmil AWG1-350 kcmil310,0 400 2*350 kcmil AWG1-350 kcmil AWG1-350 kcmilTable 18. Cable and fuse sizes for Vacon 100 (MR7 to MR9)The cable dimensioning is based on the criteria of the Underwriters’ Laboratories UL508C:Cables mustbe PVC-isolated; Max ambient temperature +30°C, max temperature of cable surface +70°C; Use onlycables with concentric copper shield; Max number of parallel cables is 9.When using cables in parallel, NOTE HOWEVER that the requirements of both the cross-sectional areaand the max number of cables must be observed.For important information on the requirements of the earthing conductor, see standard Underwriters’Laboratories UL508C.For the correction factors for each temperature, see the instructions of standard Underwriters’ LaboratoriesUL508C.4.2 Brake resistor cablesVacon AC drives are equipped with terminals for an optional external brake resistor. These terminalsare marked with R+ and R- (MR4-MR6) or DC+/R+ and R- (MR7 and bigger).24-hour support +358 (0)201 212 575 • Email: vacon@vacon.com4
vacon • 31Power cabling4.3 Cable installation• Before starting, check that none of the components of the AC drive is live. Read carefullythe warnings in chapter 1.• Place the motor cables sufficiently far from other cables• Avoid placing the motor cables in long parallel lines with other cables.• If the motor cables run in parallel with other cables note the minimum distancesbetween the motor cables and other cables given in table below.Distance betweencables, [m]Shieldedcable, [m]0.3 501.0 200• The given distances also apply between the motor cables and signal cables of other systems.• The maximum lengths of motor cables (shielded) are 100 m (MR4), 150 m (MR5 andMR6) and 200 m (MR7 to MR9).• The motor cables should cross other cables at an angle of 90 degrees.• If cable insulation checks are needed, see chapter Cable and motor insulation checks.Start the cable installation according to the instructions below:4.3.1 Frames MR4 to MR71 Strip the motor and mains cables as advised below.Earth conductorEarth conductorA1C1C2B1D1D2EMAINSMOTORFigure 19. Stripping of cables4Tel. +358 (0) 201 2121 • Fax +358 (0)201 212 205
Page 1 and 2: vacon 100ac drivesinstallation manu
Page 3 and 4: vacon • 16.3.3 Frame MR9.........
Page 5 and 6: vacon • 3EC DECLARATION OF CONFOR
Page 7 and 8: vacon • 5Safety1.2 WarningsVacon
Page 9 and 10: vacon • 7SafetyDo not perform any
Page 11 and 12: vacon • 9Receipt of delivery2.1 T
Page 13 and 14: vacon • 11Receipt of delivery2.3
Page 15: vacon • 13Receipt of delivery2.3.
Page 19: vacon • 17MountingFigure 9. Vacon
Page 22 and 23: Mounting vacon • 203.1.2.2 Flange
Page 24 and 25: Mounting vacon • 22Note that if s
Page 26 and 27: Power cabling vacon • 244. POWER
Page 28 and 29: Power cabling vacon • 264.1 UL st
Page 30 and 31: Power cabling vacon • 284.1.1.2 C
Page 34 and 35: Power cabling vacon • 32Frame A1
Page 36 and 37: Power cabling vacon • 345• Inse
Page 38 and 39: Power cabling vacon • 367Connect
Page 40 and 41: Power cabling vacon • 384.3.2 Fra
Page 42 and 43: Power cabling vacon • 40M4 x 81 2
Page 44 and 45: Power cabling vacon • 427Cut the
Page 46 and 47: Power cabling vacon • 44Connector
Page 48 and 49: Power cabling vacon • 46M4x10Figu
Page 50 and 51: Control unit vacon • 485. CONTROL
Page 52 and 53: Control unit vacon • 505.1.2 Cont
Page 54 and 55: Control unit vacon • 525.1.2.1 Se
Page 56 and 57: Control unit vacon • 54max. 40 mm
Page 58 and 59: Control unit vacon • 56Strip abou
Page 60 and 61: Control unit vacon • 58Unless alr
Page 62 and 63: Control unit vacon • 605.4 Galvan
Page 64 and 65: Commissioning vacon • 626. COMMIS
Page 66 and 67: Commissioning vacon • 646.2.1 Cab
Page 68 and 69: Commissioning vacon • 666.3.2 Fra
Page 70 and 71: Commissioning vacon • 682Further
Page 72 and 73: Commissioning vacon • 7024-hour s
Page 74 and 75: Technical data vacon • 727.1.2 Ma
Page 76 and 77: Technical data vacon • 747.2 Vaco
Page 78 and 79: Technical data vacon • 767.2.1 Te
Page 80: Find your nearest Vacon officeon th

vacon 100 installation manual - VEM motors Finland Oy

Create successful ePaper yourself

Delete template?

Save as template?